← Id 4

Volkswagen ID.4 (1st generation): Steering Diagnosis (Play, Knocking Noises)

The ID.4 uses an electromechanical power steering system with electronic control. Play and knocking noises can be caused by worn tie rod ends, damaged steering rack boots (moisture intrusion/corrosion), a faulty steering column support bearing, or software faults in the steering control module.

DifficultyMedium Time1-2 hours Steps8

Parts

4
№Part
01 Steering rack, complete with electric motorif faultyFind on Amazon →
02 Tie rod ends (inner and outer)if faultyFind on Amazon →
03 Steering rack bootsif faultyFind on Amazon →
04 Steering column support bearingif faultyFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

8 steps
  1. Check your VIN for open recall campaigns. Early ID.4 vehicles (2021-2022) were subject to recall 21V-852 for the steering gear worm gear bushing. If your vehicle is covered by the recall, contact a dealer for a free steering gear replacement.
  2. Raise the front of the vehicle on a lift (wheels off the ground) or drive it over a pit. Turn the ignition on (Ready) and have a helper quickly turn the steering wheel left and right within the 10 o'clock to 2 o'clock range (not to the stops). Listen for clicks or knocks around the steering rack and tie rod ends.
  3. Inspect the steering rack boots (left and right of the subframe). If you find tears, cracks, or grease traces on the outside, pull the boot back and check the rack shaft for moisture or corrosion. Water intrusion into the rack causes knocking and requires replacing the complete rack.
  4. Check the outer tie rod ends. Grip the end by hand and rock it up and down (without a pry bar). Any vertical play means the ball joint is worn, so replace the tie rod end.
  5. Check the inner tie rod ends (the joints on the rack). Push the tie rod back and forth. Horizontal play, or clicks during a static test (helper turns the steering wheel with the vehicle stationary), means the inner tie rod end is worn.
  6. Lower the vehicle, sit in the cabin, and switch the vehicle off. Rock the steering wheel left and right with a small amplitude. If you hear a knock near the steering column (under the dash), the problem is in the column support bearing or the intermediate shaft mounting.
  7. Connect a diagnostic scanner (VAS, VCDS, OBDeleven) to the OBD-II port under the steering column on the left. Check the steering control module (address 44) for fault codes. Codes related to the steering angle sensor, the electric motor, or the control module may point to a software fault. In some cases, reprogramming or adaptation of the control module eliminates the knocking without replacing any mechanical parts.
  8. If no mechanical damage is found but play is still present, check the tightening torque of the tie rod end nut (typical range for the MQB platform is 40-60 N·m (30-44 lb-ft); confirm the exact value in the service documentation) and of the steering rack mounting nuts to the subframe (typical range 60-80 N·m (44-59 lb-ft)).

Common mistakes and warnings

  • The ID.4 is an electric vehicle with a high-voltage battery
  • Before raising it on a lift or driving it over a pit, make sure the vehicle is off (Ready OFF) and the parking brake is applied
  • Do not touch the orange high-voltage cables under the floor
  • The steering system is electronically controlled, so after replacing the steering rack or tie rod ends, the steering wheel angle sensor must be calibrated at a dealer or with certified equipment
Spotted a mistake? Tell us →

Our articles

More articles →