https://autopapyrus.com/catalog/volkswagen/multivan/guides/turbocharger-replacement/
Volkswagen Multivan T5 2.5 TDI AXE (2008): Turbocharger Replacement
On the 2.5 TDI (AXE), the variable-geometry turbocharger (VNT) is mounted on the exhaust manifold and is connected to the engine's lubrication and cooling systems. The torque values below are approximate. Get the factory values, at least for the manifold nuts and oil line fittings, from the VW service manual for the AXE engine, and do not trust figures from forums. The main causes of turbo failure are oil starvation, foreign objects and contaminated oil. If these are not corrected, the new turbo will fail just as quickly.
Parts
8| № | Part | Alternatives |
|---|---|---|
| 01 | VNT turbocharger for 2.5 TDI AXE (174 hp), new or remanufacturedFind on Amazon → | AlternativesGarrettBorgWarner |
| 02 | Turbo and exhaust manifold gasket setFind on Amazon → | AlternativesVictor Reinz |
| 03 | Self-locking nuts and studs for turbo mountingFind on Amazon → | |
| 04 | Turbo oil feed and return line gaskets or sealsFind on Amazon → | |
| 05 | Oil feed banjo bolt sealing washersFind on Amazon → | |
| 06 | Oil filterFind on Amazon → | AlternativesMannBosch |
| 07 | Engine oilFind on Amazon → | |
| 08 | Coolant G12/G12+Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- socket set and ratchet Amazon →
- Torx and hex bits (E-Torx, 8-12 mm) Amazon →
- torque wrench 5-50 N·m (4-37 lb-ft) Amazon →
- pliers for hose clamps Amazon →
- syringe or oil can for priming the turbo with oil Amazon →
- container for draining coolant Amazon →
- jack with jack stands or a lift Amazon →
- penetrating oil (WD-40 or equivalent) Amazon →
- diagnostic scan tool with VNT actuator adaptation (VCDS or equivalent) Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 5 more.
See manuals →
Step by step
38 steps · 6 stagesStage 1 of 6 Diagnosis and preparation 6 steps
- Make sure the turbo is actually the faulty part: check shaft play (radial and axial), traces of oil in the hoses after the turbo and the intercooler, blue smoke, whistling and loss of power. First check the vacuum lines and intercooler hoses for cracks and leaks.
- Find the cause of the failure before installing a new turbo. Check the air filter housing, the filter itself and the air ducts for foreign objects. Inspect the hoses and the intercooler for oil and debris. If metal shavings or oil remain in the system, flush or replace the intercooler.
- Check the oil supply to the turbo: the line must not be clogged with carbon deposits, and the oil pressure must be normal. Replace a coked line.
- Prepare the new gaskets, self-locking nuts and washers. Lay these parts out nearby: used fasteners must not be reused.
- Disconnect the negative battery terminal (note the radio code and that the power windows will need to be reset).
- Let the engine cool completely, then raise the vehicle and secure it on jack stands.
Stage 2 of 6 Draining fluids and access 6 steps
- Drain the coolant into a clean container if coolant lines run to the turbo on your version.
- Drain the engine oil if you plan to replace it together with the filter (recommended).
- Remove the engine cover, the air duct from the air filter to the turbo and the intercooler hoses. Close the open ports with plugs or a clean cloth.
- Remove the engine undercover and, if necessary, any shields and heat shields that are in the way.
- Disconnect the wiring harnesses and connectors of the sensors and boost control solenoid valves that interfere with removal.
- To reach the assembly, you may have to remove obstructing parts: air ducts, the drive belt or brackets. The exact list depends on the trim and equipment; note the position of each part you remove.
Stage 3 of 6 Turbo removal 7 steps
- Remove the turbo heat shield (the bolts may be seized, so treat them with penetrating oil in advance).
- Disconnect the downpipe from the turbo outlet. The nuts are most likely seized: apply heat or penetrating oil and loosen them without jerking.
- Remove the banjo bolt of the oil feed line at the turbo and at the block, then remove the line and washers. Plug the openings immediately so that no dirt gets in.
- Disconnect the oil return line from the bottom of the turbo (bolts on the flange). Remove the seal.
- Disconnect the coolant lines from the turbo if your version has them. Remove the clamps and place a container underneath.
- Remove the nuts securing the manifold to the cylinder head. Remove the turbo together with the manifold or separately, depending on the design: on many VW engines the turbo comes as one unit with the manifold. Check on the vehicle.
- Remove the manifold gasket from the studs. Inspect the studs for cracks and thread damage; replace damaged ones.
Stage 4 of 6 Installing the new turbo 9 steps
- Clean the mating surfaces of the manifold and cylinder head of old gasket residue and carbon deposits without scratching the metal.
- Flush or replace the oil feed and oil return lines. Make sure the passages are clean and not clogged with carbon deposits.
- Compare the new turbo with the old one: the position of the flanges, ports and the VNT actuator. Check the engine and turbo numbers against the catalog.
- Install the new manifold gasket and mount the turbo. Install new self-locking manifold nuts and tighten them in 2-3 stages in the sequence given in the service manual (from the center outward, in a crisscross pattern). Tightening torque is per the VW service manual for the AXE. A rough guide for exhaust manifold nuts on VW diesels is about 20-35 N·m (15-26 lb-ft), but take the exact value from the manual.
- Connect the oil return line with a new seal.
- Pour 20-30 ml of clean engine oil into the turbo's oil feed port while turning the shaft by hand to lubricate the bearings.
- Connect the oil feed line with new washers. Tighten the banjo bolts with a torque wrench: at the turbo about 20-25 N·m (15-18 lb-ft) (check against the manual), at the block per the manual. Do not overtighten: the threads in the aluminum housing are fragile.
- Connect the coolant lines (if present) with new clamps or seals.
- Connect the downpipe with a new gasket and new self-locking nuts. Torque is per the manual.
Stage 5 of 6 Reassembly 5 steps
- Install the heat shield, the intercooler air hoses and the intake duct. Check that all clamps are tight and the hoses are seated fully.
- Reconnect the connectors and vacuum lines of the sensors and actuator that were removed in step 11. Check that the hoses are not kinked and do not touch hot parts.
- Install the undercover and the previously removed parts (belt, brackets, air ducts), if they were removed.
- Replace the oil filter and fill with fresh engine oil. Add coolant and bleed the air from the cooling system.
- Reconnect the battery.
Stage 6 of 6 First start and checks 5 steps
- Do not start the engine right away. Crank it with the starter for 10-15 seconds with the fuel system disabled (or with the injector connector unplugged, if possible) so that oil reaches the turbo, and only then start the engine.
- After starting, let the engine idle for 1 minute without raising the revs. Check for oil, coolant and exhaust leaks at the joints.
- Connect the diagnostic scan tool: clear the fault codes and perform the VNT actuator adaptation (basic settings) following the scan tool's procedure. Check that there are no boost pressure faults.
- Take a test drive: check boost pressure and look for whistling and smoke. After the drive, recheck the oil and coolant levels.
- Inspect the joints again for leaks and retighten the intercooler hose clamps.
Common mistakes and warnings
- This is a difficult and lengthy job
- A new turbo that has not been primed with oil in the bearings and whose oil system has not been primed will fail within the first minutes of operation
- Never install a new turbo until the cause of the old one's failure has been found and eliminated
- After installation, be sure to perform the VNT adaptation
- The hot exhaust and turbo cause burns: work only on a cold engine
- If you have no experience working on exhaust systems and no way to adapt the actuator, it is better to take the car to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Volkswagen
Volkswagen proved to the world that a car can be "the people's car": good-looking, affordable and fun.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →