https://autopapyrus.com/catalog/volkswagen/pointer/guides/engine-and-transmission-removal-and-installation/
Volkswagen Pointer 1.8 AP (2004): Engine and Transmission Removal and Installation
The 1.8 AP engine in the Pointer is mounted transversely and comes out together with the transmission as a single unit. The unit can be lifted out upward with a crane after removing the hood, or lowered out downward together with the front subframe if you have a lift. The procedure below covers lifting it out upward, which is the most practical option in a home garage. The tightening torques below are approximate. Check the exact values against the manufacturer's specifications for your vehicle.
Parts
7| № | Part |
|---|---|
| 01 | Engine oilfor refillingFind on Amazon → |
| 02 | Coolantfor refillingFind on Amazon → |
| 03 | Exhaust downpipe gasket (ring)Find on Amazon → |
| 04 | Self-locking nuts and boltsthose the service schedule says to replaceFind on Amazon → |
| 05 | Clutch kit (disc, pressure plate, release bearing)worth replacing while the transmission is removedFind on Amazon → |
| 06 | Rear crankshaft sealas neededFind on Amazon → |
| 07 | Driveshaft sealsas neededFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
11- Engine support beam or spreader bar and hoist (crane) Amazon →
- rolling stand or body jack stands Amazon →
- socket and wrench set 10-19 Amazon →
- 24 mm Amazon →
- hex and Torx bits for the driveshafts Amazon →
- torque wrench 5-50 and 40-200 N·m Amazon →
- syringe or containers for draining Amazon →
- cable ties Amazon →
- marker Amazon →
- bags for fasteners Amazon →
- thick grease for the input shaft splines Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
39 steps · 7 stagesStage 1 of 7 Preparation 6 steps
- Park the vehicle on a level surface and raise the front axle onto jack stands. If the radio has an anti-theft code, find out the code beforehand.
- With the ignition off, disconnect the negative battery terminal.
- Remove the hood: mark the hinge positions with a marker, hold the hood with a helper, unscrew the hinge bolts and set the hood aside in a safe place.
- Remove the entire air filter assembly together with the ducts and the crankcase ventilation hoses.
- Drain the coolant from the radiator and the cylinder block into a clean container.
- Drain the engine oil and, if desired, the transmission oil as well (this makes refilling easier later).
Stage 2 of 7 Disconnecting hoses, cables and wiring 8 steps
- Disconnect all cooling system hoses from the engine: to the radiator, to the expansion tank and to the heater. Remove the radiator together with the fan shroud and disconnect the fan and sensor connectors.
- Disconnect the vacuum hoses and the crankcase ventilation hoses.
- Relieve the pressure in the fuel system and disconnect the fuel supply and return hoses. Place rags underneath and plug the ends.
- Disconnect all electrical connectors from the engine, transmission, starter and alternator. Remove the ignition coil, the high-tension wires and the sensor connectors, and move the harness aside. Take photos of the connectors before removing them.
- Disconnect the accelerator cable.
- Disconnect the clutch cable or hydraulic clutch line. If the system is hydraulic, do not open the line. Instead, detach the slave cylinder from the transmission and move it aside without pressing the pedal.
- Disconnect the speedometer cable or the speed sensor connector on the transmission, and the shift linkage.
- If the vehicle has air conditioning, do not open the refrigerant circuit. Remove the compressor and move it aside with its lines attached, without kinking them. Remove the alternator drive and the power steering pump (if equipped) from their brackets and secure them to one side.
Stage 3 of 7 Driveshafts and exhaust 4 steps
- Remove the engine undercover (skid plate), if fitted.
- Undo the exhaust downpipe mounting at the manifold (about 40 N·m (30 lb-ft) as a guide for installation) and remove the downpipe together with the catalytic converter, or move it rearward.
- Disconnect both driveshafts from the transmission flanges (about 45 N·m (33 lb-ft) as a guide for installation) and tie them up to the body with wire so the joints are not damaged.
- Remove the starter if it prevents separating the transmission, or leave it in place if it comes out together with the unit.
Stage 4 of 7 Removing the engine with the transmission 5 steps
- Attach the support beam to the engine at two points: near the pulley and near the flywheel, so that the unit hangs level with a slight tilt toward the transmission. Take up the slack in the hoist without lifting.
- Remove the fasteners of the engine and transmission mounts: the right engine mount, the left transmission mount and the rear torque arm. Put the fasteners in bags and label them.
- Raise the unit with the crane by 3-5 cm and check that no wires, hoses or cables remain connected.
- Lift the unit out upward, tilting it slightly toward the transmission side so it does not catch the body, the radiator or the wiring. Watch the valve cover and the brackets.
- Set the unit on a rolling stand or on sturdy wooden blocks.
Stage 5 of 7 Separating the transmission (if necessary) 3 steps
- Remove the protective cover on the flywheel side and the cover plate on the transmission housing.
- Undo the bolts securing the transmission to the engine. Support the transmission so it does not hang on the input shaft, and remove it by pulling it straight back.
- Inspect the flywheel, clutch and seals, and replace them if necessary.
Stage 6 of 7 Installation 6 steps
- Apply a thin layer of grease to the input shaft splines. Check that the dowel sleeves are present on the cylinder block.
- Join the engine to the transmission and tighten the bolts. Approximate torques: M10 bolts about 45-60 N·m (33-44 lb-ft), M12 bolts about 75-80 N·m (55-59 lb-ft). Use the exact values from the specifications for the AP engine.
- Install the starter and the protective plates.
- Hang the unit on the support beam and carefully lower it into the engine bay, watching the driveshafts, hoses and harness. Make sure there is clearance between the unit and the driveshafts.
- First bolt the left transmission mount to the transmission and loosely to the body, then install the right engine mount and the rear torque arm. Align the unit so it does not touch the body, then tighten the mount fasteners. As a guide, torque for mount-to-body fasteners is 40-50 N·m (30-37 lb-ft). Use the exact values from the manufacturer's specifications.
- Connect the driveshafts to the transmission flanges (about 45 N·m (33 lb-ft)) and install the exhaust downpipe with a new gasket (about 40 N·m (30 lb-ft)).
Stage 7 of 7 Reassembly and checks 7 steps
- Reinstall the radiator with the fan, the A/C compressor, the alternator drive and the belt, and tension the belts according to specifications.
- Connect the fuel hoses, accelerator, clutch, speedometer cable or sensor, shift linkage, vacuum and ventilation hoses, electrical connectors and the ignition coil.
- Install the air filter, then fill the engine and transmission with coolant and oil (if they were drained).
- Connect the battery. Turn the ignition on for a few seconds to build pressure in the fuel system, and check the connections for leaks.
- Start the engine and warm it up until the fan switches on, bleed the air from the cooling system and top up the coolant. Check for oil, fuel and coolant leaks.
- Check clutch operation, gear shifting, idle speed and ignition timing (if needed). If the vehicle has an immobilizer, perform the adaptation (matching) procedure if the control unit was replaced.
- Install the hood using the marks and check the gaps. Take a test drive and recheck the fluid levels and the tightness of the mounts.
Common mistakes and warnings
- Working with a suspended engine is dangerous: do not stand under the unit, use a sound support beam and a hoist with a safe load capacity margin, and place jack stands only on solid points of the body
- The fuel system is under pressure and gasoline is highly flammable, so work away from open flames and sparks
- If you have no experience, leave the job to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Volkswagen
Volkswagen proved to the world that a car can be "the people's car": good-looking, affordable and fun.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →