← Touran Volkswagen Touran repair manuals →

Volkswagen Touran (1st generation): Driver Airbag Module Replacement

The driver airbag module is secured to the steering wheel with Torx screws and connected by a single connector to the squib (igniter). The procedure is simple, but it involves a pyrotechnic component, so you need strict discipline and the vehicle must be de-energized. Replace the module after deployment, if the housing is damaged, or as required by a recall campaign.

DifficultyMedium Time30-60 minutes Steps13

Part

№PartGenuine part no.
01 Driver airbag module (complete airbag assembly, steering wheel)by steering wheel version: two- or three-spoke, with or without multifunction buttonsFind on Amazon → 1T0880201D
1K0880201CB
5N0880201A

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

4
  • Torx socket or bit (sized to the mounting screws, usually T30-T40) Amazon →
  • thin flat-blade screwdriver Amazon →
  • 10 mm wrench for the battery terminal Amazon →
  • non-conductive mat or cloth Amazon →

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 3 more. See manuals →

Step by step

13 steps
  1. Park the car on a level surface with the wheels and steering wheel set straight ahead. Remove the key from the ignition and close the doors so nobody can accidentally switch the ignition on.
  2. Disconnect the negative battery terminal and move it aside so it can't touch the battery post. Wait at least 15 minutes: the capacitors in the SRS control unit must discharge.
  3. Remove the cover plugs or inspect the back of the steering wheel behind the spokes on the left and right. The module's mounting screws are on the sides, in holes on the rear of the steering wheel. For easier access, turn the steering wheel slightly to the side so you can see each screw.
  4. Remove both Torx screws. Don't pull the module out abruptly: it is held by the connector, and the wiring is short.
  5. Carefully lift the module toward you and place it on your lap or on the steering wheel with the front face up. Never place it face down.
  6. Release the orange locking tab on the connector at the module, then disconnect the squib connector. If the module has a second connector (horn connection), disconnect that one too.
  7. Remove the old module and set it away from the steering wheel.
  8. Connect the connectors to the new module. The orange locking tab must click into place.
  9. Install the module in the steering wheel. Don't pinch the wires, and make sure they don't interfere with the module seating.
  10. Tighten the two Torx screws evenly. Use the torque specified by the manufacturer; the exact value is not confirmed in publicly available sources. Don't overtighten: the housing is plastic, and the screws carry only a light load.
  11. Reconnect the negative battery terminal. Switch the ignition on while keeping well back from the steering wheel: the Airbag warning light should come on and go out after about 4 seconds.
  12. Press the horn: it should work. Check that the steering wheel has no play and that the gaps around the module are even.
  13. If the Airbag light stays on, read the fault codes with a diagnostic scan tool. The cause is often a poor connector contact or a previously stored deployment code that needs to be cleared. If the fault won't clear, you will need diagnostics with a scan tool that supports SRS.

Common mistakes and warnings

  • An airbag is a pyrotechnic component
  • Don't open the module, drop it, test it with a multimeter, or apply voltage to the connector
  • Store the old module face up, away from heat sources and electricity
  • Install only a serviceable module with no signs of tampering or damage
  • If you have no experience working on SRS systems, have a repair shop do the replacement
  • Your safety in a crash depends on correct installation
Spotted a mistake? Tell us →

Our articles

More articles →