Autopapyrus · Volvo XC60 2.0 D4 D4204T23 (2019)
https://autopapyrus.com/catalog/volvo/xc60/guides/glow-plug-replacement/
https://autopapyrus.com/catalog/volvo/xc60/guides/glow-plug-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Volvo XC60 2.0 D4 D4204T23 (2019): Glow Plug Replacement
Replace glow plugs when the control module reports glow circuit faults (code range P0380-P0384), the engine starts poorly when cold, or the plugs have been tested and don't heat. The main risk of this job is a seized plug: overheating and corrosion can make it snap off in the cylinder head, which then requires special extraction. So work smoothly, with no jerking, and on an engine that is warm but not hot. The torque values given below are approximate, so check them against the manufacturer's specifications.
Diagram: glow plug anatomy and what to do with each part
Tap to enlarge
- 1Hex on the plug body: put a long thin-wall socket on it. First turn 5-10 degrees counterclockwise and a little back, with smooth force.
- 2Threaded part: apply penetrating oil and wait 10-15 minutes. The plug can seize, so do not use great force.
- 3Plug contact: the connector with the wire sits on it. Disconnect the connector before unscrewing.
- 4Red connector lock: press it, do not pull on the wire or jerk.
- 5Plug tip: after removal, check for soot, melting and breakage. If a piece stayed in the head, plug the well and call a specialist.
Parts
2| № | Part | Alternatives |
|---|---|---|
| 01 | Glow plugs for Drive-E D4, same thread and length as original4 pcs, one per cylinderFind on Amazon → | AlternativesBoschNGKBeru |
| 02 | Penetrating oil (small can)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
11- Socket set and ratchet Amazon →
- long extensions Amazon →
- long thin-wall hex socket for the glow plug body hex Amazon →
- torque wrench for low torque values (up to 20 N·m (15 lb-ft)) Amazon →
- screwdriver Amazon →
- pliers Amazon →
- plastic plugs or clean rags Amazon →
- masking tape Amazon →
- compressed air Amazon →
- penetrating oil Amazon →
- multimeter Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more.
See manuals →
Step by step
24 steps · 5 stagesStage 1 of 5 Diagnosis and preparation 4 steps
- Confirm the fault: read the glow circuit codes (with an OBD scanner) and measure the resistance of each glow plug with a multimeter. A good plug has low resistance, around 0.5-2 ohms. An open circuit or a noticeably higher reading means the plug needs replacing.
- Prepare the vehicle: park on level ground, shut off the engine and let it cool to warm but not hot. Slight warmth makes removal easier, while a hot cylinder head is dangerous for your hands and for the threads.
- Disconnect the negative battery terminal. Wait a few minutes so the electronics' capacitors can discharge.
- Have clean plugs or rags ready for all open intake openings: any dirt or dropped small part in a cylinder means an expensive repair.
Stage 2 of 5 Accessing the glow plugs 4 steps
- Remove the upper decorative engine cover (pull it upward; it is held by clips or grommets).
- Locate the glow plugs along the cylinder head and find their connectors or wires. Take a photo of the harness layout and retainers so you can reassemble without mistakes.
- Remove everything that blocks access to the glow plugs on your engine: intake ducts and hoses and, if necessary, brackets and harness holders. Open up only what actually gets in the way. Immediately cover all opened hoses and openings with plugs or rags.
- Carefully disconnect the glow plug connectors and wires. Connectors are often tight and have locking tabs: press the tab, and do not pull on the wire or yank it.
Stage 3 of 5 Removing the old glow plugs 5 steps
- Before unscrewing, clean the area around each glow plug with compressed air and a soft brush so dirt doesn't fall into the cylinder head well.
- Apply penetrating oil to the threaded part of the plugs and wait 10-15 minutes.
- Fit the long thin-wall socket onto the glow plug hex and first break it loose slightly: turn it 5-10 degrees counterclockwise, then back a little. This works the threads. Apply smooth force, with no impacts.
- Unscrew the plugs one at a time. If a plug turns hard, apply penetrating oil again and repeat the rocking motion. Do not use heavy force: the plug can snap off.
- Inspect each removed plug for carbon buildup, melting or a broken tip. If a piece is left in the cylinder head, plug the well and take the car to a specialist for extraction.
Stage 4 of 5 Installing the new glow plugs 5 steps
- Compare the new plugs with the old ones: length, thread, hex and connector must all match.
- Blow out the wells with air and make sure they are clean. If necessary, carefully clean the thread in the head with a tap and a drop of oil (so no chips fall into the cylinder).
- Thread each new plug in by hand until it seats, without cross-threading, so the thread isn't stripped.
- Tighten with a torque wrench. The torque for small glow plugs is usually in the range of 8-12 N·m (6-9 lb-ft) (per the manufacturer's specification). Overtightening risks stripping the thread and breaking the plug.
- Reinstall the connectors and wires, lock them with their latches, and check that the harness doesn't touch hot parts or moving components.
Stage 5 of 5 Reassembly and check 6 steps
- Reinstall the ducts, hoses, brackets and harnesses you removed, in reverse order. Tighten the clamps and fasteners. Check the manufacturer's specifications for clamp and bracket bolt torques; a rough guide for small bolts is 8-12 N·m (6-9 lb-ft).
- Install the decorative engine cover.
- Connect the battery terminal. Turn on the ignition and check that the glow indicator on the dash lights up and goes out with no errors.
- Clear the codes with the scanner and start the engine. Listen to how it runs: a smooth idle, with no intake hissing or whistling.
- Shut off the engine and after a few minutes check that there are no leaks, fault codes or overheated wires. If a warning light is on in the dash, read the codes again.
- Dispose of the old glow plugs properly. Test the car on a cold morning start: it should be confident, with no excess smoke.
Common mistakes and warnings
- Glow plugs in a diesel cylinder head can seize: do not use heavy force, and use penetrating oil and rocking motions
- Do not try to extract a broken plug from the head yourself
- If you lack experience, it is better to leave the job to a repair shop
- Do not let dirt or foreign objects get into the cylinders or open intake pipes
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Volvo Brand
Volvo Car Corporation (originally Volvo Personvagnar AB) is a Swedish passenger car maker. The name "Volvo" is Latin…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →