← Renault

Renault Kangoo 2002 1.5 diesel: increased fuel consumption and black smoke from the exhaust

Renault Kangoo · 2002 14 answers Translated from Russian · original

A Kangoo came in with increased fuel consumption and smoke from the exhaust, soot is pouring out, you could say. I connected with Clip. The Clip screen is split into two parts with exactly the same parameters. In the upper part the values are shown in real time with the engine running, and in the lower part the same parameters are shown but frozen (static). All the parameters match each other except one, and it gave this error: DF-134 Acceleration sensor circuit. Advance - current - -4.2 *V (when I press the accelerator pedal this value increases to about + 6*V) (the same parameter in the lower, static part of the screen). When the fault appears, advance - 1020 *V (this value is constant and does not change). Please explain what this is and how to fix it.

Answers
O
Owner Oct 23, 2020

DF-134 Acceleration sensor circuit. This is probably vertical acceleration, like the DND on the Kalina. I don't understand, is the fault permanent? Advance is the injection advance, and it does change from -4.2 to + 6, that's normal. But 1020 is already a "failure" value.

O
Owner Oct 28, 2020

Yes, the fault is permanent. Clearing the error doesn't help, and it comes back the first time the engine is started. From time to time exactly the same error also appears on cylinder 3, but not every time, after clearing it, roughly after starting the engine 5 times.

O
Owner Nov 13, 2020

It drives normally, no problems. Just a smoky / sooty trail behind it, and it uses more fuel than it should.

O
Owner Jan 03, 2021

Nonsense like this could well be because of the turbo. I haven't come across this car myself, but this is the conclusion I draw from some experience with diesels, turbocharged ones.

O
Owner Aug 01, 2021

It looks like the pump is dying, or the connecting hose inside the tank has burst. It's better to pull the pump out, put it in a bucket and measure the pressure and output. Be careful with the connection, it's a fire hazard!

O
Owner Oct 29, 2021

You didn't say what type of injection pump is fitted. As I understand it, a distributor type, but with what control, cable or electronic? It would also be good to know its series (VP, VR, VE, MV, etc.). In any case, check the injection advance device. It is on the underside of the pump, below the outlets to the injectors. More precisely, check its wiring, in case it has chafed through. Between the outlets to the injectors there is a high-pressure solenoid valve, and it has wires too. And yes, smoke can come from the turbo. You can loop the oil passages on it. For a start, check the intake, to see whether there is too much oil in there.

O
Owner Nov 12, 2021

If the turbo had failed, you would feel it when driving. It looks more like the EGR or the advance control.

O
Owner Dec 18, 2021

You are wrong about the turbo there.

O
Owner Jan 06, 2022

A common rail has no injection advance sensor. It calculates the advance from the crankshaft position sensor and the throttle position sensor, and the injectors there are electronic. It is the same as a petrol engine, just without a spark :). The pump has 2 valves, one that shuts off the plunger section on top, and the other, on the side, that regulates high pressure. I think they have nothing to do with it. Injection advance is electronic, there are no valves for it. In your place I would disconnect the camshaft sensor and see how the car behaves and what error it throws. Especially since the error shows up when starting, that is, while the engine is turning. And as for the acceleration sensor, they can call any sensor that, good luck figuring it out.

O
Owner Feb 11, 2022

I'm confused too and am leaning more and more toward the turbo. By the way, something strange is going on with the ABS as well. The scanner complains about the rear left wheel sensor, and the warning lamp on the dash comes on only sometimes and stays on for roughly 1 to 3 minutes, varying. I checked the wiring continuity, it's fine, but the error still appears. I checked the sensor, it's fine, but the error still appears. I swapped the sensors between sides, and the error still appears on the same wheel. It's a madhouse.

O
Owner Apr 23, 2022

You can find out whether the smoke from the exhaust is from the turbo or not. Disconnect the oil supply passages to the turbo and loop them. If the smoke is gone, that's it, the turbo is to blame. I already wrote this. As for the ABS, you need to look at the tone ring that this "faulty" sensor reads from. The problem is most likely with it.

O
Owner May 15, 2022

If it's the turbo, the exhaust can't be mistaken for anything else: light grey with a characteristic smell of burnt oil. If the problem is with the fuel, black soot comes out. Maybe the injectors are leaking? And how does the engine run, harshly, with knocking?

O
Owner Aug 06, 2022

Well, if there were an EGR problem, there would be an EGR error. It has a position sensor and is monitored very well. And yes, it needs cleaning, with the intake manifold removed. And if it comes to cleaning, the catalytic converter also needs to be checked. But why not start with something simpler, say the temperature sensor?

Autopapyrus assistant AI assistant Sep 10, 2026

Error DF-134 with the abnormal value 1020°V when the fault appears is a clear failure in the injection advance control circuit. Black soot during normal driving points to late injection: the fuel does not burn completely. Before going into the injection pump or the turbo, check the crankshaft position sensor and its wiring. Dirt on the flywheel ring gear or play in the sensor gives exactly this picture. Another common cause on these engines is oxidized contacts in the connector of the injection advance valve (if your pump type has one). Check the valve coil resistance and the quality of the ground on the injection pump body.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →