← Daewoo

Daewoo Nubira - timing belt snapped

Daewoo Nubira · 1999 13 answers Translated from Russian · original

Daewoo Nubira, Rostov-built, 1999, 16-valve 1.6 liter engine with a catalytic converter. The timing belt snapped and bent the valves. The head was repaired, but now the car won't run properly. Spark plugs on cylinders 1 and 4 are wet, on 2 and 3 they are black. There is spark from the plug wires on all 4 cylinders. I removed the injectors and tested them on a test bench, all fine. I took off the camshafts, thinking the hydraulic lifters might not have been bled down. I bled them, reassembled and set the marks, everything lines up exactly. With the marks set, the cam lobes on cylinder 1 point inward, meaning the intake is about to open and the exhaust is almost closed, which looks like normal valve overlap. Nothing changed at all. It runs for a while with a slight misfire, then the plugs foul, and the longer it goes the worse it gets. Compression is 15 on cylinders 1 and 4 and 14 on cylinders 2 and 3. Plugs on 2 and 3 are sooty, while 1 and 4 are soaking wet. Absolute pressure is about 70 kPa, and the vacuum gauge confirms there isn't enough vacuum. Obviously this is why it pours fuel, but it's unclear what to do about it.

Answers
O
Owner Apr 16, 2021

Are the injectors leaking? Did you check the injector wiring?

O
Owner Apr 26, 2021

What do you have there, individual coils or a module? Maybe the module is faulty?

O
Owner May 07, 2021

I haven't opened up the wiring, but an external inspection showed no damage, and what damage would there be to look for when the injection time is 5-6 milliseconds at idle on a warm engine? It has a module. I swapped in one from a VAZ, the old type fits. And what is there to check on the module when a gap of a centimeter jumps from all four wires without any problem while cranking on the starter? The compression is huge and the vacuum is correspondingly poor, and that's why it floods. I just can't work out what is wrong with the hardware or how else to check it. The engine builder who did the head swears that everything is fine.

O
Owner May 27, 2021

Could the camshafts have been swapped places?

O
Owner Jun 20, 2021

It's suspicious that the cylinders misbehave in pairs. You say you checked the marks at the top, but what about the marks at the bottom, are the keys OK? Was piston 1 at TDC when you checked the marks? I think that if the mechanical side were built wrong it still wouldn't flood like this. Maybe the camshafts really are swapped, but I don't know this engine well enough to say whether that is possible.

O
Owner Jul 28, 2021

The camshafts are identical, but the gears are different, and they are in place. Of course I set TDC with a micrometer through the spark plug well, and the original mark on the bottom is off. Now I'm starting to wonder if I should set it by that mark rather than by the real TDC. I used up a terrible amount of coolant while turning that pump back and forth.

O
Owner Sep 19, 2021

Try it. Most likely something is wrong with the marks. There are no miracles in this world.

O
Owner Oct 21, 2021

I agree, the marks need checking. Maybe the key has sheared off?

O
Owner Nov 21, 2021

With such crazy compression, I think the rings are done for, at the very least. The dynamic compression will be low, so it won't run. I told you this right away.

O
Owner Jan 05, 2022

Hello! Daewoo Nubira 1998, 1.6, 16 valves. Where should the marks on the camshafts point? Thanks in advance.

O
Owner Feb 03, 2022

They should point at each other.

O
Owner Feb 12, 2022

So what's happening with the car?

O
Owner Mar 24, 2022

It's unlikely to be the rings, since the car was running and the valves were simply bent. And how high is the "huge" compression? It would be good to check the valve timing with a motor tester. What is the fuel pressure? When the engine was taken apart, were all the grounds tightened? Check continuity on all the grounds on the engine sensors and the body.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →