← SRX Cadillac SRX repair manuals →

Cadillac SRX 4.6 Northstar (2005): Alternator Replacement

The alternator on the Northstar V8 sits in a tight spot, so you have to reach it from both above and below. First, remove the drive belt and the upper mounting bolts. Then raise the vehicle, disconnect the electrical connections and take the alternator out. On AWD versions, you may need to remove the sway bar for access. Check the exact order of the lower steps and the torque specifications against the manufacturer's service manual.

DifficultyHard Time2-4 hours Steps15

Parts

2
№PartAlternatives
01 Complete alternator, 150 A, for 4.6L V8Find on Amazon → AlternativesRemyBoschBBB Industries
02 Serpentine accessory drive beltreplace at the same time if the old one is wornFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more. See manuals →

Step by step

15 steps
  1. Shut off the engine and let it cool. Disconnect the negative battery terminal and move it aside so it can't touch the body.
  2. Remove the accessory drive belt. To do this, rotate the tensioner pulley with a wrench or the special tool, slip the belt off the pulleys and slowly release the tensioner. Before removing the belt, take a photo of the belt routing so you don't make a mistake during installation.
  3. Remove the upper alternator mounting bolts. They are accessible from above, from the engine compartment.
  4. Raise the vehicle and securely support it on jack stands. Never work under a vehicle that is held up only by a jack.
  5. On AWD versions, remove the front wheel for access. Then pull out the plastic clips and remove the right front fender liner. Remove the upper and lower nuts of the left and right sway bar links, then remove the sway bar itself. On FWD versions, this step is usually not needed.
  6. Cut the plastic ties that secure the wiring harness to the alternator. Note where they were: you will need new ones in their place during reassembly.
  7. Slide the protective boot off the positive (B+) terminal on the back of the alternator. Remove the nut and take off the power wire. Then disconnect the control connector(s) by pressing the locking tab.
  8. While supporting the alternator, remove the lower mounting bolts. The alternator is heavy, so don't let it fall onto the parts nearby.
  9. Carefully maneuver the alternator out, downward or upward, depending on the available space. If some component is in the way, move it aside.
  10. Compare the new alternator with the old one: the mounting feet, pulley and terminal positions must match. If the old pulley is in good condition and the new alternator doesn't come with one, transfer it over.
  11. Install the new alternator in reverse order. First start the lower bolts by hand, then the upper ones, then tighten all the mounting bolts. Tightening torque: approximately 40-50 N·m (30-37 lb-ft) for bolts of this size; check the exact value in the manufacturer's service manual.
  12. Plug in the connector(s) and tighten the B+ power wire nut carefully, without overtightening (approximately 8-15 N·m (6-11 lb-ft); check the exact value in the manufacturer's service manual), then fit the boot. Secure the harness with new ties.
  13. If you removed them, install the sway bar, links, fender liner and wheel. Tighten the lug nuts to the vehicle's specification. Lower the vehicle.
  14. Install the drive belt following the photo of the routing. Make sure it is seated correctly in all the pulley grooves.
  15. Reconnect the negative battery terminal. Start the engine and check the voltage at the battery terminals. With the engine running, it should be about 13.5-14.7 V. Make sure no charging warning lights stay on in the instrument cluster, and listen for unusual noises.

Common mistakes and warnings

  • The B+ terminal on the alternator is live at all times while the battery is connected
  • Therefore, always disconnect the negative battery terminal before starting any work
  • Do not let a wrench short against the body
  • If a discharged battery caused the problem, test and charge it separately: the alternator is not designed to charge a deeply discharged battery
  • If you don't have experience lifting a vehicle and working on the suspension, it's better to leave the job to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →