← 2106-03

Lada 2106 1.5 (VAZ-2103, 1974): Alternator Replacement

The alternator sits on the right side of the engine and is driven by a belt from the crankshaft. To replace it, disconnect the wires, remove the belt, remove the adjusting bracket and remove the lower mounting bolt. Then take the alternator out from below. After installation, you must tension the belt.

DifficultyMedium Time1-1.5 hours Steps14

Key figures

  • Belt deflection between the alternator and the water pump
    10-15 mm at a force of about 10 kgf. This is how you check tension after installation (step 12)
  • Belt deflection between the water pump and the crankshaft
    12-17 mm at the same force. Second check in step 12
  • 10 mm wrench
    wire nut on terminal "30", steps 4 and 13
  • 17 mm wrench
    adjusting bracket nuts and the nut securing the alternator to the bracket, steps 5, 6 and 11
  • 19 mm wrench
    nut and bolt of the lower alternator mount, steps 7 and 10

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the alternator, belt and mounts are and how to remove them

Alternator from the side: pulley on top, wires belowbracket1Bar nut: 17 mm wrench2Belt on the pulley3Alternator housing4Wires with boot5Lower bolt: 19 mm wrench6Tension barTap to enlarge
  1. 1The 17 mm nut holds the alternator to the tension bar: loosen it, push the alternator with a pry bar and take the belt off.
  2. 2The drive belt runs from the crankshaft over the alternator pulley: take it off the pulley after loosening the nut.
  3. 3Alternator housing: it comes out downward between the bracket and the suspension beam.
  4. 4Wires on the housing terminals: remember how they were placed before removing them.
  5. 5The lower bolt with sleeve passes through the alternator lug, 19 mm nut: unscrew and pull it out, the alternator stays resting on the bracket.
  6. 6Tension bar: unscrew the two 17 mm nuts and remove the bar.

Parts

2
№Part
01 Complete alternator for carbureted "classic" VAZ modelsFind on Amazon →
02 Alternator drive beltif wornFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5

Step by step

14 steps
  1. Shut off the engine and let it cool. For safety, disconnect the negative terminal of the battery. You can remove the battery completely to get more room. It is easier to work from a pit or lift.
  2. Disconnect the connector from terminal "67" on the alternator housing.
  3. Remove the ring terminal from the neutral (ground) wire terminal.
  4. Slide the insulating boot off the large terminal "30". Use a 10 mm wrench to remove the nut and take off the wires. Remember how they were positioned.
  5. Loosen the 17 mm nut that secures the alternator to the adjusting bracket. Use a pry bar to push the alternator toward the cylinder block and take the belt off the alternator pulley.
  6. Use a 17 mm wrench to remove the two nuts and take off the adjusting bracket.
  7. Remove the nut of the lower alternator mount (19 mm wrench). Pull out the bolt and the spacer sleeve. The alternator will stay resting on the bracket.
  8. Take the alternator out downward, between the bracket and the front suspension crossmember. If you can't move the alternator with the pry bar without a lot of force, or it won't come out, remove the engine splash shield (skid plate).
  9. Compare the new alternator with the old one: pulley, mounting feet, terminal locations. If the pulley needs to be swapped, transfer it from the old unit.
  10. Install the alternator in reverse order: first the lower bolt with the sleeve, then the adjusting bracket. Leave the lower nut and the bracket nuts not fully tightened for now.
  11. Put the belt on the pulleys. Use a pry bar to push the alternator away from the engine to tension the belt. Hold it in that position and tighten the nut that secures it to the bracket. Then tighten the lower nut.
  12. Check the belt tension: when pressed with a force of about 10 kgf (about 98 N), the belt span between the alternator pulley and the water pump should deflect 10-15 mm. The span between the pump and the crankshaft should deflect 12-17 mm.
  13. Reconnect the wires: onto terminal "30" with the 10 mm nut and the boot, onto the neutral (ground) wire terminal, then the connector onto "67". Install the splash shield if you removed it. Reconnect the battery.
  14. Start the engine. The charging warning light on the instrument panel should go out. Check the voltage at the battery terminals with the engine running, usually around 13.5-14.5 V. Check the belt tension again after 100-200 km (60-125 miles): a new belt stretches.

Common mistakes and warnings

  • Tightening torques for the alternator fasteners are not given in the available materials
  • Tighten the nuts firmly, but without excessive force, so you don't strip the threads
  • Check exact values against the manufacturer's specifications
  • An overtightened belt quickly ruins the alternator and water pump bearings, and a loose one slips and squeals
  • Do not remove the wires from terminal "30" while the battery is connected: this spot often sparks and shorts to the body
Spotted a mistake? Tell us →