← 2106-03

Lada 2106-03 1.5 (VAZ-2103, 1974): Lubrication System Maintenance

The VAZ-2103 engine has a combined lubrication system: some components are lubricated under pressure from a gear-type oil pump, and others by splash. Maintenance comes down to changing the oil and filter, checking the oil level and pressure, and checking the crankcase ventilation. The system's fill capacity, including the filter, is about 3.75 L (3.96 qt).

DifficultyEasy Time40-60 minutes Steps13

Key figures

  • How much oil you need
    about 3.75 L (3.96 qt) including the filter. Add it gradually, checking the dipstick (steps 7, 9)
  • Which oil
    API SF/SG/SH/SJ, most often 10W-40 or 15W-40. It suits most climates (Part)
  • Normal oil pressure
    3.5-4.5 kgf/cm² (about 50-64 psi) on a warm engine. If it is much lower, look for the cause (step 10)
  • When to change oil and filter
    about every 10,000 km. The first maintenance is at 2,000 km (step 12)
  • Oil pump drive sprocket bolt
    41-51 N·m (30-38 lb-ft). Only if you are disassembling the pump drive (step 13)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the drain plug and oil filter are and how to find them from below

View of the engine underside from the left, from the pitFront of the carRearLeft side of the engineThe same spot with the filter removed1Drain plug212 mm hex key in the plug3Oil pan4Oil filter5Seating surfaceTap to enlarge
  1. 1Drain plug at the bottom of the deep part of the pan: unscrew it to drain the oil, then screw it back firmly but without excess force, the thread strips easily.
  2. 2The 12 mm hex key sits on the plug head: it is used to unscrew and tighten the plug.
  3. 3Stamped steel oil pan under the engine: the oil drains into it.
  4. 4Oil filter on the left side of the engine: unscrew with a puller or by hand, fill the new one with oil, oil the seal and tighten by hand only.
  5. 5Seating surface on the block with the threaded stud: wipe it with a rag after removing the filter.

Parts

3
№PartAlternatives
01 Engine oil API SF/SG/SH/SJ, seasonal viscosityFind on Amazon →
02 Full-flow spin-on oil filter for classic-layout VAZ enginesFind on Amazon → AlternativesMannBoschFiltron
03 Drain plug sealing ringif equippedFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6

Step by step

13 steps
  1. Warm the engine up to operating temperature, ideally right after a drive, since warm oil drains more completely. Park the car on level ground or over a pit, set the parking brake and shut off the engine.
  2. Open the hood and remove the oil filler cap so the oil drains faster.
  3. Place a drain pan of 4 L (4.2 qt) or larger under the oil pan. Remove the drain plug with the hex key (size per VAZ specification: 12 mm) and drain all the oil.
  4. Unscrew the oil filter (it is on the left side of the engine) with a filter wrench or by hand. Wipe the mounting surface on the block with a rag.
  5. Reinstall the drain plug. For the plug tightening torque, check the manufacturer's specification; tighten it firmly but without excessive force, because the pan is stamped steel and the threads strip easily.
  6. Fill the new filter with fresh oil, lubricate its rubber sealing ring with oil, and screw it onto the block by hand until it touches, then tighten it a further turn by hand. Do not tighten the filter with a wrench.
  7. Pour fresh oil in through the filler neck, going by the dipstick: the level must be between the MIN and MAX marks. The capacity is about 3.75 L (3.96 qt) including the filter, but add oil gradually and let it drain down into the pan.
  8. Start the engine and let it run for a few minutes. The low oil pressure warning light should go out shortly after startup. Shut off the engine.
  9. After 10 minutes, inspect the filter and drain plug for leaks, check the dipstick level again and top up if needed.
  10. Oil pressure: on a warm engine at medium rpm, the norm is about 3.5-4.5 kgf/cm² (about 50-64 psi). The dashboard light comes on when pressure drops to roughly 0.4-0.8 kgf/cm² (about 6-11 psi). If the light is on with a warm engine at idle, or the pressure is clearly below normal, check the oil level, the condition of the pressure sensor, and the condition of the pump and bearing shells.
  11. This engine has a closed positive crankcase ventilation system, with gases routed through an oil separator. Periodically clean the ventilation hoses and the flame arrester, per the schedule every 20,000 km. Clogging causes oil to be forced out through seals and gaskets.
  12. Service schedule: change the oil and filter at every maintenance interval, in general about every 10,000 km (after break-in, the first maintenance is at 2,000 km), and flush the lubrication system every 30,000 km. For a high-mileage car built in 1974, shorten the interval if the oil darkens quickly.
  13. If you are removing the oil pan or the oil pump: tighten the oil pan bolts (M6) to 5-8 N·m (44-71 lb-in), and the oil pump drive sprocket bolt (M10x1.25) to 41-51 N·m (30-38 lb-ft). The pump is secured to the block with two 13 mm bolts. With the pan removed, inspect the oil pickup screen and clean it.

Common mistakes and warnings

  • Take used oil and filters to a collection point; do not pour them on the ground
  • Do not fill oil above the MAX mark, because the excess goes into the crankcase ventilation and causes seal leaks
  • Do not overtighten the filter with a wrench: the gasket will tear and the filter will then be impossible to remove
  • If oil pressure drops or the oil light flashes, do not run the engine, because the bearing shells can fail within minutes
Spotted a mistake? Tell us →