← 2106-03

Lada 2106 (Gen 1): Instrument Cluster Replacement

The instrument cluster on the VAZ-2106 is held by clips and spring retainers. It has no screws or nuts. To replace it, disconnect the battery, remove the steering column covers, pull the cluster out of the dash, and disconnect the speedometer cable and wiring connectors. You do not need to remove the steering wheel.

DifficultyEasy Time30-60 minutes Steps14

Key figures

  • Gauge backlight bulbs
    W4W (AMH12-4). These are the bulbs for the speedometer, tachometer, and the fuel, temperature, and oil pressure gauges (step 12)
  • Indicator bulbs
    W3W (AMH12-3). These are for the cluster icons: battery charge, high beam, turn signals, etc. (step 12)
  • Number of harness connectors on the cluster
    2. This is how many connectors you need to disconnect from the back of the cluster (step 9)
  • Number of rocker switches with connectors
    3. Remove the connector from each one, noting the wire positions (step 10)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: cable nut, blocks and switches on the cluster back

Rear view of the cluster pulled out of the dash1234567Speedometer cable nutHarness block near tachometerHarness block at bottomThree rocker switchesBulb socketsSpeedometerTachometerSame sockets with wires around each gaugeTap to enlarge
  1. 1Knurled speedometer cable nut on the back: unscrew it by hand and disconnect the cable.
  2. 2Instrument panel harness block near the tachometer: disconnect it from the cluster harness.
  3. 3Second harness block at the bottom of the cluster: disconnect it too.
  4. 4Three rocker switches with blocks: remember or photograph the wire positions, then remove the blocks.
  5. 5Bulb sockets around the gauges: move them to the new cluster if needed.
  6. 6Speedometer: the large left gauge.
  7. 7Tachometer: the second large gauge.

Parts

3
№Part
01 VAZ-2106 instrument cluster assemblyFind on Amazon →
02 W4W backlight bulb (AMH12-4)if replacing along with the clusterFind on Amazon →
03 W3W indicator bulb (AMH12-3)if replacing along with the clusterFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

2
  • Flat-blade screwdriver, thin screwdriver or metal rod, awl, wrench for the battery terminal Amazon →
  • scissors are not needed Amazon →

Step by step

14 steps
  1. Park the car on level ground, shut off the engine, and set the parking brake.
  2. Disconnect the cable from the negative terminal of the battery.
  3. Remove the steering column covers (trim).
  4. Reach under the dash and disconnect the wire from the carburetor choke cover (air damper) warning switch.
  5. Pry the upper part of the cluster with a screwdriver and work it out of the dash.
  6. If the top of the cluster does not come free, use an awl to pierce two holes in the marked spots on the underside of the dash. Use a thin screwdriver or rod to press the spring retainers and pull out the lower part of the cluster.
  7. Pull the cluster out of the dash as far as it will go so you can reach the back panel.
  8. Unscrew the knurled nut on the speedometer cable by hand and disconnect the cable.
  9. Disconnect the two connectors of the dash wiring harness from the cluster harness.
  10. Remember or mark the wire positions, then disconnect the connectors from the three rocker switches.
  11. Remove the cluster.
  12. Transfer any needed parts to the new cluster if they are not included. The backlight bulbs (speedometer, tachometer, fuel level, temperature, and oil pressure gauges) are W4W (AMH12-4). The indicator bulbs (low fuel, oil pressure, parking brake, battery charge, choke, exterior lights, turn signals, high beam) are W3W (AMH12-3).
  13. Install the new cluster in reverse order: connect the switch connectors, the two harness connectors, the speedometer cable (tighten the nut by hand only), and the choke warning switch wire. Press the cluster into the dash until it clicks, then install the steering column covers.
  14. Connect the negative battery terminal. Turn the ignition on and check the backlight, indicator lights, and gauges. Check the speedometer while driving.

Common mistakes and warnings

  • Be sure to disconnect the battery before you start
  • There are many live wires behind the cluster
  • Before you remove the connectors from the switches, memorize or photograph the wire positions, or it is easy to mix them up later
  • Do not pull the cluster with force if it will not come out
  • Check whether it is still held by the retainers, and use the method in step 6
  • Torque specifications are not needed for this job
Spotted a mistake? Tell us →