← 2106-03

Lada 2106 (VAZ-2106, 1st generation): Manual Transmission Repair

The VAZ-2106 (1976, 1.6 engine) has a four-speed gearbox with inertia synchronizers. The gearbox case is split, and the rear cover comes off separately. Repair is most often needed for grinding and jumping out of gear (worn synchronizers and shift forks), bearing whine and leaking seals. The repair can only be done with the gearbox removed from the car. The torque values below are approximate, so check the exact values against the manufacturer's specifications.

DifficultyHard Time1-2 daysremoval and installation 3-5 hours, disassembly and inspection separate Steps14

Key figures

  • Oil for the four-speed gearbox
    1.35 L (1.4 qt), the amount to fill after the repair (step 13); viscosity 75W-90, class GL-4 or GL-5
  • Break-in after repair
    about 500 km, the distance to avoid hard launches and abrupt shifts (step 14)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the input shaft, clutch bell and engine bolts are

View of the gearbox from above: clutch bell closest to us3 studswith nuts1Gear lever with boot2Rear cover3Gearbox case4Clutch housing (bell)5Clutch housing bolts4 bolts at the flange corners6Input shaftTap to enlarge
  1. 1Gear lever with boot: removable, taken off first. The boot and base sit on three studs with nuts.
  2. 2Rear cover with shift mechanism: forks and rods are under it. Removed separately after the clutch housing.
  3. 3Gearbox case: split, shafts and gears inside. Oil drains through the plug at the bottom.
  4. 4Clutch housing (bell): attaches the gearbox to the engine. Removed from the gearbox before disassembly.
  5. 5Clutch housing bolts to the engine: four at the flange corners. Undone while the gearbox is supported by a jack.
  6. 6Input shaft: long splined shaft in the center of the bell. It must come fully out of the clutch disc; never load it with the gearbox weight.

Parts

6
№PartAlternatives
01 Transmission repair kit (shaft bearings, input and output shaft seals, snap rings)Find on Amazon →
02 Synchronizer blocking ringsif wornFind on Amazon →
03 Synchronizer sleeves and hubsif wornFind on Amazon →
04 Shift forksif wornFind on Amazon →
05 Transmission gearsif wornFind on Amazon →
06 Gear oil GL-4 or GL-5, 75W-90Find on Amazon → AlternativesLukoilCastrolShell

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Step by step

14 steps
  1. Park the car over a pit or on ramps, switch off the engine and disconnect the negative battery terminal. Drain the oil from the gearbox (drain plug on the bottom of the case), placing a drain pan underneath beforehand.
  2. Remove the gear shift lever: the guide sleeve, ball joint and boot are attached to the gearbox rear cover with three studs and nuts. The lever is removable specifically to make gearbox removal easier.
  3. Disconnect the driveshaft from the gearbox flange (first mark the relative position of the flanges with paint) and lower the shaft down. Plug the opening in the rear cover so that residual oil does not leak out.
  4. Disconnect the wires of the reverse light switch, the speedometer cable or drive, and the clutch release linkage (slave cylinder or fork), and remove the starter. Disconnect the exhaust downpipe if it is in the way.
  5. Support the gearbox with a jack or stand, and remove the rear gearbox mount crossmember together with the mount cushion.
  6. Remove the bolts securing the clutch housing to the engine. Slide the gearbox straight back along its axis until the input shaft is completely out of the clutch disc and clutch assembly, without letting the weight of the gearbox hang on the shaft. Lower the gearbox and take it out.
  7. Clean the outside of the gearbox and secure it on a bench. Remove the clutch housing, then the rear cover with the shift mechanism: the forks are fixed to the rods with bolts, and the rods are held by ball detents (spring under the cover) and three interlock pins. When pulling out the rods, take care not to lose the balls, springs and pins.
  8. Disassemble the shafts: the input shaft sits in the rear bearing in the front wall of the case. The output shaft rests on three bearings: a needle bearing in the end of the input shaft, an intermediate bearing in the rear wall of the case (held by a bolted plate) and a rear double-row bearing in the rear cover. The rear output shaft bearing is clamped by a nut with a bent-tab lock washer, so bend the washer back before undoing the nut. Remove snap rings with pliers and bearings only with a puller.
  9. Inspect the parts: gear teeth (chipping, spalling), synchronizer blocking rings and cones (worn teeth, a smooth friction surface means the ring must be replaced), shift forks (wear in the sleeve grooves), the needle bearing, any noisy bearings and the seals. If the gearbox has been opened before, check that the synchronizers are complete.
  10. Replace the bearings, the input and output shaft seals, and any worn synchronizer rings and forks. Lubricate the sliding surfaces with gear oil during assembly.
  11. Reassemble the gearbox in reverse order: the order of parts on the shafts must strictly follow the order in which they came off. Press the bearings on with a drift applied to the outer race, then tighten the rear bearing nut and lock it by bending the washer tab. Tighten the fastening bolts with a torque wrench to the range specified for the thread size. Check that the shafts turn freely and that all gears engage without binding.
  12. Install the gearbox in the car in reverse order. Before mating, lightly lubricate the input shaft splines and make sure the shaft enters the clutch disc without misalignment. Do not pull the gearbox in with the bolts until it has seated fully against the engine.
  13. Fill with GL-4 or GL-5 oil, 1.35 L (1.4 qt) for the four-speed gearbox, filling to the lower edge of the fill hole. 75W-90 oil is suitable for year-round use.
  14. Check the clutch linkage adjustment and run through all gears with the car raised. Test drive: listen for noise and check for jumping out of gear and leaks. For the first 500 km or so, do not stress the gearbox with hard launches or abrupt shifts.

Common mistakes and warnings

  • The gearbox is heavy, so it is best to remove and install it with a helper and with a support under the gearbox
  • Do not work under a car held up only by a jack
  • Use jack stands or a pit
  • Never let the weight of the gearbox hang on the input shaft during removal and installation, as this damages the clutch disc and the shaft bearing
  • If you have no experience disassembling synchronizers, then in the case of serious wear it is cheaper and more reliable to replace the gearbox as a complete unit from a trusted source than to assemble one from mixed parts
Spotted a mistake? Tell us →