Autopapyrus · Citroen C3 1.4 8v TU3 (2006)
https://autopapyrus.com/catalog/citroen/c3/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/citroen/c3/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Citroen C3 1.4 8v TU3 (2006): Engine Oil and Oil Filter Change
On the first-generation C3 with the 1.4 8v (TU3) engine, you change the oil together with the cartridge filter, which sits in a housing on the front of the engine. The approximate change interval is 10,000 km or once a year, whichever comes first. The job is easiest on a warm engine, but be careful not to burn yourself.
Diagram: where the oil filter and drain plug are and how to find them
Tap to enlarge
- 1Oil filter housing cap on top of the engine: unscrew it with a 27 mm socket together with the old filter and ring.
- 2Drain plug on the oil pan on the right front wheel side: undo it with an 8 mm hex key, the oil is hot.
- 3Coolant hose next to the filter housing: do not damage it while working.
- 4Wiring harness with a connector next to the filter: do not damage it either, and lay rags under the housing.
- 5Engine oil pan: the cast part under the engine, the plug sits on its side.
- 6Right front wheel: a landmark showing which side to look at, the plug is near the suspension arm by the wheel.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Cartridge oil filter for 1.4 TU3 (replaceable element in a housing with a cap) with new cap O-ringFind on Amazon → | AlternativesMahle/KnechtMannBosch |
| 02 | Copper drain plug sealing washerFind on Amazon → | |
| 03 | Engine oil, synthetic, PSA approval, ACEA A3/B4about 3-3.5 L (3.2-3.7 qt)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- 8 mm hex socket bit with ratchet (oil pan drain plug) Amazon →
- 27 mm socket with ratchet (filter housing cap) Amazon →
- torque wrench Amazon →
- drain pan of at least 5 L (5.3 qt) Amazon →
- funnel Amazon →
- syringe or suction bulb for removing oil from the filter housing Amazon →
- shop rags Amazon →
- brake cleaner Amazon →
- drive-on ramps or a lift Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more.
See manuals →
Step by step
22 steps · 4 stagesStage 1 of 4 Preparation 4 steps
- Warm up the engine for 5-10 minutes to normal operating temperature: warm oil drains more completely.
- Park the car on level ground and set the parking brake. Drive the front onto ramps or raise it on a lift (the low front bumper catches on ramps, so lay boards down to make a gentler approach). If you use a jack, always place jack stands.
- Shut off the engine. Open the hood and remove the oil filler cap so the oil drains faster.
- Get the new drain plug washer, the filter with its O-ring and the drain pan ready.
Stage 2 of 4 Draining the old oil 4 steps
- Locate the drain plug on the oil pan on the right front wheel side. If the underbody shield has access plugs, remove the one you need. Don't confuse it with the transmission plug: that one has an internal square drive, while the engine plug takes an 8 mm hex.
- Position the drain pan, loosen the plug with the 8 mm hex bit and unscrew it by hand (the oil is hot).
- Let the oil drain for at least 10-15 minutes. Inspect the plug and the pan for metal shavings.
- Replace the copper washer with a new one, wipe the threads and the sealing surface, install the plug and tighten it with a torque wrench to about 25-35 N·m (18-26 lb-ft) (check the exact value in the manufacturer's specifications). Don't overtighten: the threads in an aluminum pan strip easily.
Stage 3 of 4 Replacing the filter 7 steps
- Lay rags under and around the filter housing: some oil will spill when you remove the cap, and that is unavoidable. Cooling system hoses and a wiring harness run nearby, so don't damage them.
- If necessary, remove the air duct that blocks access (on many versions it comes off by hand without tools).
- Use the 27 mm socket to unscrew the filter housing cap and pull out the old filter element together with the cap.
- Remove the rubber O-ring from the old cap and install the new one from the kit, lightly lubricating it with clean oil.
- Use a syringe to remove the remaining oil from the housing (about 100 g), then wipe the housing and the threads with a clean rag.
- Insert the new filter element into the cap, screw the cap in and tighten it to about 20-25 N·m (15-18 lb-ft) (check the exact value in the manufacturer's specifications). Don't use force: the plastic housing can be damaged.
- Degrease the oil-soaked areas with brake cleaner so you don't mistake fresh drips for a leak later.
Stage 4 of 4 Refilling and checking 7 steps
- Lower the car onto level ground.
- Pour in about 3 L (3.2 qt) of oil through the funnel, wait a couple of minutes, then check the level with the dipstick.
- Add oil in small amounts up to the MAX mark (not above it), pausing 2-3 minutes each time to let it drain into the pan. Close the filler neck.
- Start the engine for 1-2 minutes (the oil pressure light should go out within a couple of seconds) and check for leaks at the drain plug and the filter cap.
- Shut off the engine, wait 5 minutes, check the dipstick again and top up to MAX if needed.
- Reset the service interval indicator: turn the ignition off, press and hold the trip reset button on the instrument cluster, turn the ignition on and wait for the countdown to reach zero, then release the button.
- Take the used oil and filter to a collection point. Don't pour them down the drain.
Common mistakes and warnings
- Drain oil from a hot engine carefully, as you can get burned
- Don't use a jack without stands, and don't work under a car supported only by a jack
- Don't overfill the oil above the MAX mark
- The torque values above are approximate, so check the exact values in the manufacturer's specifications
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Citroën Brand
Citroën is an automaker founded in France in 1919 by André Citroën. Since 1976 it has been part of the PSA Peugeot…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →