Autopapyrus · Daihatsu Cast 0.66 turbo KF-DET (2015)
https://autopapyrus.com/catalog/daihatsu/cast/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/daihatsu/cast/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Daihatsu Cast 0.66 turbo KF-DET (2015): Engine Oil and Oil Filter Change
The KF-DET turbo engine runs under severe-duty conditions, so change the oil more often than on naturally aspirated versions. Guideline for turbo: every 2,500-5,000 km or every 3-6 months. The filter should be changed at least every other oil change, but on a turbo it is wiser to change it with every oil change. The refill capacity is approximately 3 L (3.2 qt) (for the naturally aspirated KF-VE with filter, it is 2.9 L (3.1 qt)). Check the exact capacity and viscosity in the owner's manual.
Key figures
- Oil refill capacityabout 3 L (3.2 qt). This is roughly what you need with a new filter; add oil in stages and check with the dipstick (steps 17-18)
- Turbo change interval2,500-5,000 km or 3-6 months. Whichever comes first is when to change the oil (summary)
- Wait time after startup5-10 minutes. This is how long to wait before the final level check (step 22)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: tools and parts for the oil and filter change
Tap to enlarge
- 1Oil filter: unscrew the old one; on the new one oil the rubber ring and hand-tighten, then about 3/4 turn more.
- 2Cup filter wrench slips onto the filter and unscrews it counterclockwise. Do not overtighten when installing.
- 3Ratchet slips onto the cup wrench and gives leverage for unscrewing the filter.
- 4Drain plug at the bottom of the oil pan: loosen counterclockwise, last turns by hand.
- 5New plug washer: replace the old one when refitting the plug.
- 6Plug wrench: check the size against the plug, usually 14-17 mm.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | 0.66 L turbocharged gasoline engine oil, API SN or higherabout 3 L (3.2 qt) per fillFind on Amazon → | |
| 02 | Oil filter for KF-DET engine (Daihatsu Cast LA250S)Find on Amazon → | AlternativesToyota/DaihatsuVicBosch |
| 03 | Drain plug washernewFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8Step by step
25 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Warm up the engine for 5-10 minutes so the oil becomes thin. Hot oil and the drain plug can burn you, so after warming up, shut off the engine and wait 5-10 minutes.
- Park the car on level ground and set the parking brake. If you lift the car with a jack, always place jack stands under it. Never work under a car supported only by a jack.
- Open the hood and remove the oil filler cap. This lets the oil drain faster.
- Get the new oil, filter and new drain plug washer ready.
Stage 2 of 5 Draining the oil 5 steps
- If there is a plastic skid plate under the engine, remove it (fasteners are bolts or plastic clips).
- Find the drain plug at the bottom of the oil pan and position the drain pan with plenty of margin: the oil comes out in an arc.
- Loosen the plug with a wrench counterclockwise. Unscrew the last few turns by hand, holding the plug so it doesn't fall into the oil.
- Let the oil drain for 10-15 minutes, until only occasional drops remain.
- Wipe the plug and its seat, and replace the drain plug washer with a new one.
Stage 3 of 5 Replacing the filter 5 steps
- Find the oil filter on the engine block. Position the drain pan and rags, since the remaining oil will run out of the filter.
- Unscrew the old filter counterclockwise with the filter wrench. Make sure the old sealing ring does not stay stuck on the block's mounting surface.
- Wipe the mounting surface with a clean rag.
- Lubricate the rubber gasket of the new filter with fresh oil. For better priming, you can pour a little oil into the filter if it sits upright.
- Spin the filter on by hand until the gasket touches the surface, then tighten about another 3/4 turn. The exact torque or tightening angle is printed on the filter packaging. Do not overtighten with the wrench, or you won't be able to remove the filter next time.
Stage 4 of 5 Refilling 5 steps
- Install the drain plug with the new washer. Tightening torque is approximately 30-40 N·m (22-30 lb-ft) (confirm the exact value in the Daihatsu service manual). Do not overtighten: threads in an aluminum oil pan strip easily.
- Reinstall the skid plate if you removed it.
- Using a funnel, pour in about 2.5 L (2.6 qt) of oil and wait a minute for it to drain into the pan.
- Check the level with the dipstick and add oil in small amounts up to the MAX mark. Do not overfill: excess oil damages the turbocharger and seals.
- Screw on the oil filler cap.
Stage 5 of 5 Checking 6 steps
- Start the engine without touching the accelerator. The oil pressure light should go out within 2-5 seconds. Let it idle for 1-2 minutes (the turbo fills with oil).
- Inspect the filter and drain plug for leaks. If there are any, tighten carefully or replace the washer or gasket.
- Shut off the engine, wait 5-10 minutes, and check the dipstick again on level ground. Top up to the mark if needed.
- Pour the used oil into a container and take it to a recycling or collection point. Do not pour it down a drain or onto the ground.
- Reset the maintenance interval indicator if your instrument cluster has one (see the owner's manual for the procedure).
- Write down the mileage and the date of the change.
Common mistakes and warnings
- Oil and engine parts are hot after driving, so wear gloves
- Do not use oil whose viscosity and specification do not match the owner's manual: the turbo is very sensitive to lubricant quality
- Always support a jacked-up car with jack stands
- The torque values above are approximate, so confirm the exact values in the manufacturer's service manual