← C-Max Ford C-Max repair manuals →

Ford C-Max 1.8 (2008): On-Vehicle Alternator and Charging Circuit Test

On this engine, the powertrain control module (PCM) controls charging. It sets the alternator voltage based on battery temperature and electrical load. The test measures battery terminal voltage with no load and under load, then checks voltage drops on the ground side and the positive cable. Before you test the alternator, make sure the battery and belt are in good condition.

DifficultyEasy Time30-45 minutes Steps17

Key figures

  • No-load battery voltage at 1500 rpmnormal for a healthy alternator, measured with a multimeter at the battery terminals (step 4)
    14.1-15.1 V
  • Voltage rise under load at 2000 rpmif it does not rise, look for losses on the ground and positive sides (step 5)
    at least 0.5 V above the starting voltage
  • Voltage drop on the ground side and on the positive cablehigher means a poor connection, so clean and tighten the terminals (steps 6-7)
    less than 0.5 V each
  • Regulator supply at the alternator connectorif lower, the supply circuit is faulty (step 9)
    more than 10 V
  • Voltage when the regulator failsthe alternator is in fail-safe mode and needs diagnosis (step 12)
    about 13.5 V

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the regulator, connector, B+ terminal and housing are on the alternator

Alternator seen from the rear, regulator side1Voltage regulator2Alternator connector3B+ terminal with nut4Housing: alternator groundribbed plate on the rearTap to enlarge
  1. 1Voltage regulator: the ribbed plate on the rear of the alternator. If readings are low, replace the alternator as an assembly.
  2. 2Alternator connector: unplug with ignition off and measure supply voltage at the harness pin (over 10 V).
  3. 3B+ terminal: the power stud with a nut. Measure between it and the battery positive (under 0.5 V); clean and tighten if poor.
  4. 4Alternator housing: ground. Measure between it and battery negative (under 0.5 V); clean and tighten the mounting if needed.

Parts

3
№PartGenuine part no.
01 Complete alternator for 1.8 Duratecif faultyFind on Amazon → 1530298
02 Batteryif neededFind on Amazon →
03 Accessory drive beltif neededFind on Amazon → 1760376
1731697

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

2
  • Digital multimeter, standard wrench set (for cleaning and tightening terminals), a helper to switch on electrical loads Amazon →
  • for reading engine control module codes, a diagnostic scan tool Amazon →

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more. See manuals →

Step by step

17 steps
  1. Inspection. Check the accessory drive belt (cracks, slack, slipping), the alternator mounting, fuses, connectors and wiring harnesses, the battery terminals and the heavy-gauge cables. Fix any obvious faults before you take measurements.
  2. Charging warning light. Normally it comes on when you switch the ignition on and goes out after the engine starts. If it stays on with the engine running, the control module has seen a fault for about 20 seconds. The cause could be voltage out of range, an internal alternator failure or lost communication with the module. If the light does not come on with the ignition on, check the bulb in the instrument cluster, its circuit and the alternator.
  3. Battery check. A battery with a poor charge gives false readings. Charge a discharged battery before you judge the alternator. If you have a battery tester, remove the surface charge (turn on the high beams, rear window heater and blower for one minute, switch everything off and wait at least 5 minutes) and test the battery. Replace a faulty battery.
  4. No-load voltage. Switch off all electrical consumers and the ignition. Connect the multimeter to the battery terminals and record the starting voltage. Start the engine and hold it at about 1500 rpm with no load. Normal voltage is 14.1-15.1 V. If the voltage rise over the starting voltage is less than 2.5 V, go to step 5. If it is more than 2.5 V, you need to diagnose it with a scan tool.
  5. Voltage under load. With the engine running, turn on the A/C (if equipped), set the heater blower to maximum and switch on the high beams. Raise the engine speed to 2000 rpm. The voltage should rise at least 0.5 V above the starting voltage. If it does, the charging system is good. If not, continue with step 6.
  6. Ground-side voltage drop. With the ignition on (engine not running), measure the voltage between the alternator housing and the negative battery terminal. It should be less than 0.5 V. If it is higher, clean and tighten the alternator mounting, the engine-to-body ground strap and the negative battery cable. If that does not help, replace the negative cable.
  7. Positive-side voltage drop. With the ignition on, measure the voltage between the alternator B+ output terminal and the positive battery terminal. It should be less than 0.5 V. If it is higher, clean and tighten the positive cable connections.
  8. B+ terminal supply. Measure the voltage between the alternator B+ terminal and ground. It should equal battery voltage. If it does not, the circuit from the battery through the starter to the alternator is damaged.
  9. Regulator supply. Switch the ignition off and disconnect the alternator connector. Measure the voltage at the supply pin of the harness-side connector against ground. It should be more than 10 V. If it is lower, repair the supply circuit.
  10. Control module codes. Reconnect the connector, switch the ignition on and read the engine control module codes with a scan tool. If there are codes, diagnose the alternator-to-module communication circuit using those codes. If there are no codes, but steps 4-9 showed insufficient voltage, the alternator is faulty and must be replaced as a complete unit.
  11. Normal readings by key position. Ignition off: about 10-12 V at the battery and at the B+ terminal, and the light is off. Ignition on, engine not running: the same 10-12 V, and the light is on. Engine running: 13-15 V, and the light is off.
  12. Alternator load after starting. This is normal behavior. The control module switches the alternator off while the starter is cranking, then ramps up its output gradually. Voltage is higher with a cold battery and lower with a warm one. Under high load or low voltage, idle speed may rise by about 150 rpm. If regulation fails, the alternator runs at a fixed voltage of about 13.5 V. The car will still drive, but you should have it diagnosed.
  13. Protective functions. When voltage drops below about 10.3 V, the module switches off consumers one at a time at 5-second intervals: the heated windshield, the heated rear window, then the A/C. When voltage rises above about 16 V, the window heaters switch on to shed load. If you notice this behavior, the charging circuit is faulty.
  14. Radio interference check. Remove the accessory drive belt, switch the ignition on and briefly start the engine with the radio on. If the interference does not go away, the alternator is not the cause. If it goes away, clean and tighten the ground and positive connections. If that does not help, replace the alternator.
  15. Excessive noise. Check the belt and its tension, then the alternator mounting bolts. If the noise continues, replace the alternator.
  16. Parasitic drain while parked. If the battery goes flat even though the alternator is good, check whether the trunk, glove box or interior lights stay on with the ignition off.
  17. Conclusion. If steps 4-5 gave normal values, the alternator is good, and you should look for the cause of the discharge in the battery or in consumers that draw current with the ignition off. If the measurements are normal but the light stays on, diagnose the light circuit through the instrument cluster.

Common mistakes and warnings

  • Do not disconnect the battery terminal with the engine running
  • A voltage spike can damage the electronics
  • Keep your hands, clothing and wires away from the belt and pulleys when you test with the engine running
  • No torque values are needed for this test
  • When you tighten terminals and ground straps, do not use excessive force, or you may strip the threads
  • If you lack experience, it is best to take the car to a repair shop for alternator replacement and for any work on connectors and the control module
Spotted a mistake? Tell us →

Our articles

More articles →