Autopapyrus · Ford Focus III 2.0 GDI (2015)
https://autopapyrus.com/catalog/ford/focus/guides/throttle-body-cleaning/
https://autopapyrus.com/catalog/ford/focus/guides/throttle-body-cleaning/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Ford Focus III 2.0 GDI (2015): Throttle Body Cleaning
The Focus III has an electronic throttle body and no separate idle air control valve. Carbon buildup on it causes a fluctuating or high idle speed. On the 2.0 engine the buildup is usually heavier because of exhaust gas recirculation. It is best to remove the throttle body and clean it off the car. Cleaning it in place is possible, but the result is not as good.
Key figures
- Socket size for the throttle body screwsthis is what removes the throttle body in step 7Torx T30, 4 screws
- Tightening torque for the throttle body screwstorque wrench in step 12; the screws thread into plastic, so don't overtightenabout 10 N·m (89 lb-in)
- Wait time before starting workuntil the electronics shut down (step 2)30-40 minutes
- Idle warm-up after reassemblyuntil the idle speed stabilizes (step 15)5-10 minutes
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the throttle body sits on the manifold and how it is fastened
Tap to enlarge
- 1Four Torx T30 bolts hold the throttle body to the intake manifold. Remove them and do not drop them into the engine bay; when reassembling, tighten crosswise to about 10 N·m.
- 2Throttle body: round throttle housing with the electric actuator at the side. Remove it and clean it off the car, without spraying cleaner on the actuator and sensor.
- 3Gasket between the throttle body and the manifold. Inspect it: if torn or hardened, prepare a new one.
- 4Electrical connector: press the lock and pull the plug sideways off the socket on the body. When reassembling, push it in until it clicks.
- 5Intake manifold: the throttle body mounts on it. With the body removed, cover the opening with a clean rag.
Parts
2| № | Part |
|---|---|
| 01 | Throttle body cleaner (aerosol, safe for electronic sensors and plastic)Find on Amazon → |
| 02 | Ford Focus 2.0 throttle body gasketonly if the old one is damagedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- Torx T30 socket or bit with a ratchet Amazon →
- 7 mm wrench or screwdriver for the hose clamp (depending on the clamp screw size) Amazon →
- flat-blade screwdriver Amazon →
- pliers Amazon →
- torque wrench for low torque (up to 10 N·m (89 lb-in)) Amazon →
- throttle body cleaner or carb cleaner spray Amazon →
- cotton swabs Amazon →
- lint-free wipes Amazon →
- gloves Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 25 more.
See manuals →
Step by step
16 steps · 5 stagesStage 1 of 5 Preparation 3 steps
- Shut off the engine and let it cool down. Remove the decorative engine cover if it is in the way.
- Lock the car and wait 30-40 minutes so the electronics "go to sleep." Owners on forums do this. You don't have to disconnect the battery terminal. If you do disconnect it, you will need to let the idle relearn after reassembly.
- Locate the throttle body. It sits on the intake manifold, with the corrugated rubber intake duct from the air filter housing attached to it.
Stage 2 of 5 Removal 5 steps
- Disconnect the electrical connector from the throttle body. Press the locking tab and pull the connector sideways.
- Loosen the duct clamp on the throttle body side. Squeeze the clamp on the air filter housing with pliers or pry it open with a screwdriver.
- Disconnect the small hoses (crankcase ventilation) from the duct and remove the duct. It may fit tightly on the throttle side, so loosen the clamp completely first.
- Remove the 4 Torx T30 screws that hold the throttle body to the intake manifold. Don't drop the screws into the engine bay. Before removal, you can mark the position of the connector and duct with a marker so you can reassemble everything the same way.
- Remove the throttle body. Inspect the gasket between the throttle body and the manifold. If it is torn or hardened, get a new one ready.
Stage 3 of 5 Cleaning 3 steps
- Cover the intake manifold opening with a clean wipe so nothing falls in.
- Spray cleaner on the throttle plate and into the bore, and let it sit for 1-2 minutes. Remove the buildup with cotton swabs and wipes. Don't push hard on the throttle plate. It is spring-loaded and moves with resistance, and too much pressure can damage the actuator.
- Don't pour cleaner on the housing with the electric motor and sensor. Don't disassemble the plastic housing with the motor and sensors. Wipe everything dry and allow 5-10 minutes for evaporation.
Stage 4 of 5 Reassembly 2 steps
- Install the throttle body on the manifold with the gasket. Tighten the 4 screws in a crisscross pattern. The tightening torque is about 10 N·m (89 lb-in). The screws thread into plastic, so don't overtighten them.
- Fit the duct: first onto the air filter housing, then onto the throttle body. Tighten both clamps, reconnect the small hoses, and plug in the electrical connector until it clicks. Reinstall the decorative cover.
Stage 5 of 5 Check and relearn 3 steps
- Turn the ignition on for a few seconds without starting the engine, then turn it off. The electronic throttle recalibrates itself every time the ignition is switched off.
- Start the engine and let it idle for 5-10 minutes. The idle speed may first rise to 1500-2000 rpm and then drop to normal. If it still fluctuates after that, repeat the cycle "ignition on for a few seconds, off for 10 seconds" 2-3 times and warm up the engine again.
- If you disconnected the battery terminal and the idle is still not stable, drive several dozen kilometers in mixed conditions. The control module will update the adaptation on its own. If the Check Engine light comes on or the fault remains, read the code with an OBD scanner.
Common mistakes and warnings
- The torque values are approximate
- Check the exact value against the manufacturer's specifications
- Don't press hard on the throttle plate with your finger, and don't put metal objects into the bore
- If throttle-related faults remain after cleaning, the cause is more often the electronics or the throttle actuator, and that needs diagnostics
- On the 2.0, a failed throttle body is usually replaced as a complete unit
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →