Autopapyrus · Ford Kuga II (2018)
https://autopapyrus.com/catalog/ford/kuga/guides/low-beam-bulb-replacement/
https://autopapyrus.com/catalog/ford/kuga/guides/low-beam-bulb-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Ford Kuga II (2018): Low Beam Bulb Replacement
On a Kuga II with halogen headlights, you reach the low beam bulb from the engine compartment. You remove the rear cover of the headlight, disconnect the connector and pull out the bulb. If the car has bi-xenon headlights (D3S bulb) or LED headlights, have this work done at a repair shop, because xenon systems use high voltage. This guide is for halogen bulbs.
Key figures
- Number of screws holding the headlight3 pcs. This only matters if the bulb can't be reached through the cover and the whole headlight has to be removed (step 5).
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the low beam bulb is and how to reach it from the engine bay
Tap to enlarge
- 1Low beam bulb cover: the outer one, farthest from the car centre. Remove it: release the metal clip or unscrew counterclockwise.
- 2High beam cover: separate, do not touch it when changing the low beam.
- 3Rubber rim of the cover: when refitting, the cover must sit evenly on the seal, otherwise moisture gets in.
- 4Headlight housing with connector: if the bulb is out of reach, move aside the hose or cover in the way, or remove the whole headlight.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Halogen low beam bulb H7 or H11, 12 V ("LL" version has a longer service life)2 pcs, replace as a pairFind on Amazon → | AlternativesOsramPhilipsBoschNarva |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
2
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 7 more.
See manuals →
Step by step
17 steps · 4 stagesStage 1 of 4 Preparation 4 steps
- Turn off the engine, the lights and the ignition. If the headlights were just on, wait 10-15 minutes for the bulb to cool down.
- Open the hood. Identify which bulb in your headlight is the low beam: it is usually the outer one (farthest from the center of the car), behind a cover on the back of the headlight. The high beam and the parking light have separate covers.
- Make sure you have a halogen headlight. If there is no ordinary bulb with a base behind the headlight, and instead there is a xenon unit with a high-voltage wire, this is repair shop work, so do not continue.
- If access is blocked by a hose or a cover, move them aside. If you still can't reach the bulb, remove the whole headlight (steps 5-7 below).
Stage 2 of 4 Accessing the bulb 3 steps
- Only if you can't reach the bulb. Open the hood and turn off the lights. Remove the three screws that hold the headlight, carefully pull the headlight forward until it clears the lower mounting point, lift the outer side and remove the headlight. Disconnect the headlight's electrical connector.
- Find the rear cover of the low beam bulb. Unclip the metal retaining clip or unscrew the bayonet cover counterclockwise (depending on the headlight version).
- Remove the cover and set it in a clean place so that dust doesn't get into the housing.
Stage 3 of 4 Replacing the bulb 5 steps
- Disconnect the electrical connector from the bulb base: press the locking tab and pull the connector toward you.
- Release the bulb: either move aside the spring retaining clip, or turn the base counterclockwise (depending on the headlight design), then pull the bulb straight out.
- Note the position of the old bulb: the base has tabs and a slot, and the bulb fits only one way.
- Take out the new bulb, holding it only by the base. Do not touch the glass with your hands: oil from your fingers causes overheating and quick burnout. If you do touch it, wipe the glass with rubbing alcohol and let it dry.
- Insert the bulb into the headlight, aligning the tabs with the slots, and secure it with the clip or by turning it clockwise until it stops. The bulb must not wobble.
Stage 4 of 4 Reassembly and check 5 steps
- Push the connector onto the bulb base until it clicks.
- Put the rear cover back: it must seat evenly against the seal, or moisture will get into the headlight. Close the clip.
- If you removed the headlight, set it on the lower mounting point, plug in the connector and secure it with the three screws. The tightening torque is low: tighten without force until the headlight sits flush, and check the exact value in the manufacturer's service manual.
- Turn on the low beam and check both headlights, then the high beam. Make sure there is no flickering and the connector isn't getting hot.
- Do the same on the other headlight if you are replacing them as a pair. Check the beam aim against a wall: both light patterns should be at the same height. If the light points the wrong way after removing the headlight, adjust it with the headlight leveling adjuster.
Common mistakes and warnings
- Do not touch the glass bulb with your fingers, and do not turn the bulb on outside the headlight: it gets very hot
- If the car has xenon (D3S bulbs) or LED headlights, do not work on them yourself: the circuit carries high voltage, so have a repair shop do the replacement
- Always replace bulbs with the ignition off
- Tightening torques for this job are minimal, so check the exact values for the headlight screws in the manufacturer's service manual
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Ford
Ford Motor Company is the largest American automaker by heritage and one of the most recognizable car brands in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →