Autopapyrus · GAC GS8 2.0 Turbo 4C20J1 (2021)
https://autopapyrus.com/catalog/gac/gs8/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/gac/gs8/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
GAC GS8 2.0 Turbo 4C20J1 (2021): Engine Oil and Oil Filter Change
On the GS8 with this engine, change the oil and oil filter every 10,000 km or once a year, whichever comes first. This matters for a turbo engine because the oil lubricates and cools the turbocharger. Change the oil with the engine warm, and always install a new filter.
Key figures
- Oil and filter change interval10,000 km or 1 year, whichever comes first. This is your guide for when to do the job (steps 1-18)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Engine oil, API SN or newer (semi-synthetic or synthetic)volume not specifiedFind on Amazon → | |
| 02 | Engine oil filter 4C20J1Find on Amazon → | AlternativesMannBoschFiltron |
| 03 | Drain plug sealing washerif not built into the plugFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7Step by step
18 steps- Warm up the engine for 5-10 minutes so the oil thins out and drains completely. Park the car on level ground and set the parking brake.
- Shut off the engine and wait 5-10 minutes. The oil will drain down into the oil pan, and the pan and drain plug will cool a little. Hot oil can burn you, so be careful.
- Open the hood and remove the oil filler cap. This lets air into the engine so the oil drains faster.
- Raise the car or drive it over the pit. If there is an engine undercover (skid plate), remove it (usually a few bolts).
- Find the drain plug at the bottom of the oil pan. Place the drain pan under it with plenty of clearance on the sides, because the oil stream first shoots out at an angle.
- Remove the plug and let the oil drain for 10-15 minutes, until only occasional drops remain.
- Wipe the plug and its seat. Replace the sealing washer if it is a separate part or if it is dented.
- Thread the plug in by hand, then tighten it with a torque wrench. The torque for an aluminum oil pan is usually 25-40 N·m (18-30 lb-ft); check the exact value in the manufacturer's service data. Do not overtighten, as you can strip the threads in the pan.
- Locate the oil filter (on turbo engines it is usually on the side of the cylinder block or at the bottom of the engine). Position the drain pan, because the remaining oil will run out when you unscrew it. If the filter is a cup or cartridge type inside a housing, remove the housing cap.
- Unscrew the old filter with a wrench or filter tool. Make sure the old gasket has not stayed stuck to the mounting surface, because a double gasket causes a heavy leak.
- Lubricate the rubber seal of the new filter with fresh oil. For a canister-type filter, pour a little oil into it if it will sit upright.
- Spin the new filter on by hand until the gasket touches, then tighten it about 3/4 of a turn or to the mark on the filter. For a housing with a cap, use the torque from the manufacturer's service data. Do not tighten it as hard as possible with a wrench.
- Reinstall the engine undercover if you removed it, and lower the car onto its wheels.
- Using a funnel, pour about 4.5-5 L (4.8-5.3 qt) of oil into the filler neck. Check the exact quantity in the service data, as it depends on the engine and filter. Let the oil drain down into the pan for 1-2 minutes.
- Check the level with the dipstick. It should be between the MIN and MAX marks. Add oil in small amounts (0.2-0.3 L (0.2-0.3 qt) at a time) until it reaches the upper half of the scale.
- Put the cap back on the oil filler neck. Start the engine and run it for 30-60 seconds. The oil pressure light should go out right after startup. If it stays on, shut off the engine immediately and find the cause.
- Inspect the drain plug and filter. There should be no leaks. Shut off the engine, wait 5 minutes, and check the dipstick again. Top up if necessary.
- Reset the service interval counter in the instrument cluster menu, if the car has one. Take the used oil to a recycling point.
Common mistakes and warnings
- Work only on a lift, in a pit, or on reliable jack stands
- Never get under a car that is held up by a single jack
- Use only oil with the specification and viscosity listed in the owner's manual, because the wrong oil on a turbo engine speeds up turbocharger wear
- If you lack experience or tools, have a repair shop do the job