← Valdai Next

GAZ Valdai Next Cummins ISF2.8 (2021): Water Pump Removal and Installation

The pump is a centrifugal, belt-driven unit. Its inlet and bypass passages are cast into the front cover of the cylinder block, and the pump is secured to the cover with eight bolts. To reach it, you need to drain the coolant and remove the radiator, drive belt and viscous fan clutch with the fan. You do not need to remove the thermostat. This guide covers the water pump, not the thermostat.

DifficultyMedium Time3-4 hours Steps25

Key figures

  • Pump bolt torque (8 bolts)
    8 N·m (6 lb-ft). Set it on the torque wrench in step 16 and tighten evenly. Do not overtighten, as you can damage the mounting surface.
  • Fan wrench
    32 mm. Open-end wrench for the fan's threaded hub (steps 10 and 17).
  • Coolant fill capacity
    about 15 L (15.9 qt). Have this much ready for filling in step 20.
  • Belt seating check
    2 crankshaft revolutions. After installing the belt, check that it sits in the grooves (step 18).

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the water pump sits on the engine front cover and how it is fastened

Front of the engine cover and the new pump with gasketHoseOil coolerCover without pump, front viewNew pump with gasketThe pump sits on the cover1Water pump2Rubber gasket3Eight pump bolts4Impeller: six blades5Pump inlet passage6Pump seat on the coverTap to enlarge
  1. 1Water pump: centrifugal, belt driven. Bolted to the front cover of the cylinder block. Remove it and fit the new one in the same place.
  2. 2Rubber gasket: follows the outer outline of the pump, including the inlet pocket. Remove the old one, clean the seat, fit the new one from the kit. Do not use sealant instead of a gasket.
  3. 3Eight pump bolts: undo them to remove the pump. When installing, thread them by hand, then tighten evenly in a criss-cross pattern to 8 N.m.
  4. 4Impeller: six blades around the hub. On the removed pump there must be no scoring or damaged blades.
  5. 5Inlet passage: the opening in the front cover for the pump inlet. It is part of the cover and is left alone.
  6. 6Seat on the cover: round recess with the shaft opening and the gasket outline. Clean it of gasket remains and dirt.

Parts

4
№PartAlternatives
01 Cummins ISF2.8 water pump (rubber gasket included)Find on Amazon → AlternativesLuzar
02 ES Compleat or Cool Stream Premium coolantfill capacity about 15 L (15.9 qt)Find on Amazon →
03 Drive beltif neededFind on Amazon →
04 O-ringsif neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

25 steps · 5 stages
Stage 1 of 5 Preparation and coolant draining 5 steps
  1. Shut off the engine and let it cool down completely. Open the hood.
  2. Turn the ignition on, set the heater temperature control to maximum, then turn the ignition off. This lets coolant drain from the heater core as well.
  3. Disconnect the negative battery terminal.
  4. Remove the air filter housing and the front bumper (they block access to the radiator).
  5. Place a drain pan under the vehicle, slip a hose onto the radiator drain valve and open the valve plug 2-3 turns. Remove the expansion tank cap so the coolant drains completely. Drain the coolant.
Stage 2 of 5 Removing parts to reach the pump 5 steps
  1. Disconnect the upper and lower radiator hoses and the air bleed hose.
  2. Remove the two bolts securing the radiator to the frame base and take out the radiator together with the fan shroud.
  3. Remove the intercooler, since it blocks access to the fan.
  4. Remove the drive belt. Using a wrench on the idler pulley bolt (16 mm socket), turn the tensioner arm clockwise and slip the belt off the pulleys. If you will reuse the belt, mark its direction of rotation.
  5. Remove the fan with the viscous clutch: using a 32 mm wrench, turn the threaded hub counterclockwise and remove it together with the fan.
Stage 3 of 5 Removing the pump 3 steps
  1. Remove the eight bolts securing the pump to the front cover of the cylinder block and take off the pump.
  2. Remove the rubber gasket. Clean the mounting surface on the cover of any gasket residue and dirt.
  3. Inspect the removed pump: the impeller must have no scoring or damaged vanes, and the shaft must have no play. Traces and deposits around the weep hole are not a reason to replace the pump, but a constant leak from it is.
Stage 4 of 5 Installation 6 steps
  1. Compare the new pump with the old one (mounting holes, pulley, impeller). Position the new gasket from the kit.
  2. Place the pump on the cover and thread in the eight bolts by hand.
  3. Tighten the bolts evenly in a crisscross pattern to 8 N·m (6 lb-ft).
  4. Install the fan with the viscous clutch and tighten the threaded hub with a 32 mm wrench. Use the torque specified by the manufacturer.
  5. Install the drive belt. Routing: alternator, two idler pulleys, power steering pump, tensioner pulley, water pump pulley, fan pulley, crankshaft. Turn the crankshaft 2 revolutions and make sure the belt ribs sit properly in the pulley grooves.
  6. Install the intercooler and the radiator with the shroud, tighten the two radiator mounting bolts, and reconnect the hoses and the air bleed hose. Install the bumper and the air filter housing.
Stage 5 of 5 Refilling and checking 6 steps
  1. Close the radiator drain valve. Pour coolant in through the expansion tank.
  2. If the level stops dropping, squeeze the lower radiator hose several times to push out trapped air.
  3. Unscrew the plug on the pipe running from the water distributor to the heater core. Close it once coolant begins to flow out.
  4. Reconnect the battery, start the engine, top off the coolant and close the tank. The white tank cap is rated for the higher pressure of the Cummins system, so do not fit a different one.
  5. Warm up the engine until the thermostat opens (it opens at about 95 °C) and run it at various RPM. Bring the coolant to the correct level.
  6. Check the pump, hoses and weep hole for leaks. Recheck the coolant level after a few days.

Common mistakes and warnings

  • Work only on a cold engine: the system is under pressure, and hot coolant causes burns
  • Used coolant is toxic, so dispose of it properly
  • Do not use sealant in place of the gasket
  • Check the manufacturer's specification for the tightening torque of the fan hub and the tensioner pulley bolts
  • If there is a leak or overheating after the replacement, stop using the vehicle and inspect the system
How it works · 3D How the Engine Cooling System Works How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →