Autopapyrus · Geely Boyue (Atlas / Coolray class SUV) 1.5 TD (181 hp) (2023)
https://autopapyrus.com/catalog/geely/boyue/guides/engine-oil-and-oil-filter-replacement/
https://autopapyrus.com/catalog/geely/boyue/guides/engine-oil-and-oil-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Geely Boyue (Atlas / Coolray class SUV) 1.5 TD (181 hp) (2023): Engine Oil and Oil Filter Replacement
The 1.5 TD engine (JLE-3G15TD) requires 0W-20 viscosity oil and an oil change every 7,000-8,500 km depending on the season. The filter is a cartridge type installed from underneath. The refill capacity is about 6 L (6.3 qt), up to the MAX mark on the dipstick.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Geely oil filterFind on Amazon → | AlternativesHengst H98WMahle OC614FiltronMann |
| 02 | Engine oil 0W-20 API SP or higher6 L (6.3 qt)Find on Amazon → | |
| 03 | Drain plug gasketFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Step by step
13 steps- Warm the engine up to operating temperature, shut it off, and raise the car on a lift or ramps, or position it over a pit.
- Open the oil filler cap to equalize the pressure.
- Remove the engine undercover (if installed) and place the drain pan under the drain plug.
- Use a 17 mm wrench to remove the drain plug and let the oil drain completely (10-15 minutes).
- Replace the drain plug gasket, thread the plug in by hand until it stops, then tighten it with the wrench another quarter turn (tightening torque 25-35 N·m (18-26 lb-ft)).
- Use the filter wrench to unscrew the oil filter housing from the bottom of the engine and remove the old cartridge.
- Install the new filter element into the housing and replace the rubber O-ring.
- Lubricate the O-ring with clean oil, thread the filter housing on by hand until it makes contact, then tighten it another three-quarters of a turn.
- Pour 5.5 L (5.8 qt) of oil through the filler neck, wait 2-3 minutes, and check the level with the dipstick.
- Top up the oil to a level between the MIN and MAX marks, then close the filler cap.
- Start the engine, let it idle for 1-2 minutes, shut it off, and wait 5 minutes.
- Check the level with the dipstick. It should be between MIN and MAX. Add 100-200 mL (3.4-6.8 fl oz) if necessary.
- Inspect the drain plug and filter for leaks, then reinstall the engine undercover.
Common mistakes and warnings
- Do not use oil with a viscosity higher than 0W-20
- The engine is designed for low-viscosity oils, and deviating from the specification leads to increased wear and higher fuel consumption
- Dispose of used oil at a designated collection facility
Spotted a mistake? Tell us →
Our articles
Before you buy
German Turbo Engines vs. Chinese Ones: Which Lasts Longer? An Honest Look at Engine Life
Volkswagen 1.4 and 2.0 TSI, BMW N20 and Mercedes M274 versus Haval, Chery and Geely engines: lifespan benchmarks…
Read →
Brand stories
The History of Geely
In its early years, Geely focused on making refrigerators. In 1992 it began producing motorcycle parts, and two years…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →