Autopapyrus · Haval F7x 1.5 turbo GW4B15A (2021)
https://autopapyrus.com/catalog/haval/f7x/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/haval/f7x/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Haval F7x 1.5 turbo GW4B15A (2021): Engine Oil and Oil Filter Change
Change the oil in the 1.5 turbo engine with the engine warm, together with the filter. The catalog fill capacity is about 3.7 L (3.9 qt). In practice, about 4 L (4.2 qt) goes in, so top up using the dipstick. Follow the service booklet for the change interval. For city driving and short trips, changing more often (every 7-8 thousand km or less) is the safer choice. This guide is for the GW4B15A engine. The 7DCT transmission does not affect this job.
Key figures
- Oil capacity per catalog data3.7 L (3.9 qt) (about 4 L (4.2 qt) in practice). This is the amount to add in steps 14-15. Use the dipstick for the final level.
- Oil viscosity0W-20. This is specified for the related GW4B15D engine, so check it against the oil filler cap before buying.
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the drain plug, filter cap, dipstick and undershield are
Tap to enlarge
- 1Drain plug on the ribbed aluminium oil pan. Put the container with room to spare: oil comes out as a jet forward. Undo with a 14 wrench (check against the plug), then by hand. Oil is hot, wear gloves. Refit with a new washer, torque about 25-40 Nm.
- 2Black plastic oil filter cap with a hex head. Undo with a 27 socket and pull out the cartridge with its seals. Fit a new one and tighten with a torque wrench to no more than about 25 Nm: do not overtighten plastic.
- 3Engine undershield: plastic panel on bolts. If fitted, remove it (remember the bolt positions). The filter is visible in the opening of the shield and is reached through it.
- 4Oil dipstick with an orange handle by the engine. Check the level 2-3 minutes after filling and top up by 100-200 ml to the MAX mark, never above.
- 5Decorative engine cover. If it covers the oil filler neck, remove it, unscrew the filler cap, and refit everything afterwards.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Synthetic engine oil4-5 L (4.2-5.3 qt)Find on Amazon → | |
| 02 | Oil filter for GW4B15A engine (cartridge with sealing rings or spin-on)Find on Amazon → | AlternativesMannBoschFiltron |
| 03 | Drain plug washerFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- Socket or 14 mm wrench for the drain plug (check the size against your plug) Amazon →
- 27 mm socket for the oil filter housing cap (check against your cap) Amazon →
- torque wrench Amazon →
- drain pan of 5 L (5.3 qt) or larger Amazon →
- funnel Amazon →
- oil filter wrench (if the filter turns out to be a spin-on type) Amazon →
- jack and jack stands or a lift Amazon →
- gloves Amazon →
- shop rags Amazon →
Step by step
22 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Warm up the engine for 5-10 minutes so the oil thins out, then shut it off. Wait 5 minutes for the oil to drain down into the oil pan.
- Park the car on level ground and set the parking brake. Raise the front of the car on a lift or on a jack with jack stands, or drive it onto ramps.
- Get the new oil, filter and a new drain plug washer ready. Before starting, check the floor under the car and lay down some cardboard.
- Open the hood and remove the decorative engine cover if it covers the oil filler neck. Unscrew the filler cap, which speeds up draining.
Stage 2 of 5 Draining the oil 4 steps
- If there is an engine undercover, remove it (the fasteners are usually bolts, so remember where each one goes).
- Locate the drain plug at the bottom of the oil pan. Position the drain pan with some margin: the oil comes out in a stream that shoots forward.
- Loosen the drain plug with a 14 mm wrench (check the size against your plug) and unscrew it by hand, then move the pan out of the way of the stream. The oil is hot, so wear gloves.
- Let the oil drain for 10-15 minutes. Wipe the plug and its seating surface, and replace the washer.
Stage 3 of 5 Replacing the filter 5 steps
- Find the oil filter on the underside or side of the engine block. On the GW4B15A this is usually a plastic cap with a cartridge inside (other Haval engines may use a spin-on filter). Position the drain pan and rags, because the oil from the housing will run downward.
- If the filter is in a housing: unscrew the cap with a 27 mm socket and pull out the old cartridge together with its rings. If it is a spin-on filter: unscrew it counterclockwise with an oil filter wrench.
- Remove the old sealing rings from the cap and clean the seating area of dirt. Lubricate the new rings with fresh oil.
- Insert the new cartridge, thread the cap on by hand, then tighten it with a torque wrench. The torque for the filter cap is no more than about 25 N·m (18 lb-ft) (a guideline only; follow the manufacturer's specification for the exact value). Do not overtighten the plastic. For a spin-on filter, lubricate the seal with oil and tighten it by hand until it touches, plus 3/4 of a turn.
- Install the drain plug with the new washer and tighten it with a torque wrench: approximately 25-40 N·m (18-30 lb-ft) (follow the manufacturer's specification for the exact value).
Stage 4 of 5 Filling with oil 3 steps
- Insert the funnel into the oil filler neck and pour in about 3.5 L (3.7 qt) of oil.
- Wait 2-3 minutes and check the level with the dipstick. Top up in small amounts (100-200 mL each) up to the MAX mark. The total is usually about 3.7-4 L (3.9-4.2 qt).
- Close the filler cap and reinstall the decorative cover if you removed it.
Stage 5 of 5 Check 6 steps
- Start the engine and let it run for 1-2 minutes without touching the throttle. The oil pressure light should go out a few seconds after startup.
- Inspect the drain plug and the filter cap for leaks, and tighten if necessary.
- Shut off the engine, wait 5 minutes, and check the level on the dipstick again, then top up to the mark.
- Reinstall the engine undercover and lower the car.
- Reset the service interval following the instructions for your car (through the instrument cluster menu, if the function is available) and write down the mileage of the oil change.
- Take the used oil and old filter to a collection point. Do not pour them onto the ground.
Common mistakes and warnings
- The oil is very hot after the engine has been running
- Do not drain it right after shutting the engine off, and wear gloves
- Always secure a car raised on a jack with jack stands
- Do not fill above the MAX mark: excess oil foams and damages the turbocharger and seals
- The torque values above are guidelines only
- Check the exact values against the manufacturer's specification
Spotted a mistake? Tell us →
Our articles
Before you buy
Used Haval F7: Recalls, Engines, Gearbox and 5 Checks Before You Buy
Two recalls, oil consumption after 100,000 km, the quirks of the dual-clutch gearbox and five checks before buying a…
Read →
Before you buy
German Turbo Engines vs. Chinese Ones: Which Lasts Longer? An Honest Look at Engine Life
Volkswagen 1.4 and 2.0 TSI, BMW N20 and Mercedes M274 versus Haval, Chery and Geely engines: lifespan benchmarks…
Read →
Brand stories
The History of Great Wall Motors
Great Wall Motors Ltd. has been one of China's largest automakers since 1995. It is essentially a holding company that…
Read →