https://autopapyrus.com/catalog/haval/m6/guides/rear-brake-pad-replacement/
Haval M6 (2025): Rear Brake Pad Replacement
The Haval M6 has rear disc brakes and an electric parking brake: the electric motor is built into the rear caliper. Because of this, before removing the caliper you need to put the actuator into service mode and retract the piston, otherwise the pads cannot be spread apart. This guide covers the rear axle. The front pads are easier to replace, since there is no electric actuator.
Key figures
- Lug nut wrenchremove the wheel and tighten the lug nuts again (steps 2 and 20)19 mm
- Caliper wrenchesremove the caliper bolts (step 10)13 mm and 15 mm
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Rear disc brake pad set (one axle) for Haval M61 set per axle, with anti-squeal shims and spring clips, if included in the setFind on Amazon → | AlternativesBremboTRWFerodo |
| 02 | Caliper guide pin greaseFind on Amazon → | |
| 03 | Rear brake rotorsif the edge is worn or deeply groovedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
10- jack and two jack stands Amazon →
- 19 mm lug wrench Amazon →
- 13 mm and 15 mm wrenches Amazon →
- torque wrench Amazon →
- wire brush Amazon →
- copper (ceramic) grease for caliper guide pins Amazon →
- brake cleaner Amazon →
- wire or hook for hanging the caliper Amazon →
- C-clamp or piston retraction tool Amazon →
- diagnostic scan tool with electronic parking brake (EPB) service function Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
25 steps · 6 stagesStage 1 of 6 Preparation 5 steps
- Park the vehicle on a level surface, turn off the engine, and switch the ignition off. Place wheel chocks under the front wheels.
- Loosen the lug nuts on the rear wheels (19 mm wrench) by half a turn while the wheel is still on the ground. Remove the decorative caps from the nuts first.
- Raise the rear of the vehicle at the factory jacking points and set it on jack stands. Do not rely on a jack alone.
- Remove the wheels.
- Inspect the rotor: deep grooves, cracks, or a high lip around the edge mean it is better to replace the rotors along with the pads.
Stage 2 of 6 Retracting the electronic parking brake 3 steps
- Connect the scan tool and activate the EPB service mode (brake pad replacement mode). Make sure the system shows service mode and the actuator has retracted the pistons. The pads cannot be spread by hand without this.
- Do not apply 12 V directly to the motor and do not disconnect the actuator "blindly": this may be done only as a last resort, and incorrect connection will damage the actuator or caliper. If service mode will not activate, it is better to take the car to a repair shop.
- While the system is in service mode, do not press the parking brake button.
Stage 3 of 6 Removal 5 steps
- Disconnect the electric actuator connector on the caliper if the scan tool instructions require it after retraction.
- Remove the caliper mounting bolts with the 13 mm and 15 mm wrenches. Hold the guide pin with a second wrench if necessary.
- Lift the caliper off the pads and hang it from the suspension spring with wire. Never leave it hanging by the brake hose.
- Remove the old pads, and note the positions of the spring clips and anti-squeal shims.
- Remove the caliper bracket only if the rotor needs to be replaced. Its bolts are tightened to the manufacturer's specified torque.
Stage 4 of 6 Installing the new pads 4 steps
- Clean the pad seats on the bracket with a brush and clean the rotor with brake cleaner.
- Inspect the caliper boots and guide pins: they should move freely. Lubricate them with a thin layer of the proper grease. No grease should get on the pad friction surfaces or the rotor.
- Install the new spring clips and pads in their places. The friction material (lining) must face the rotor.
- If the piston is not fully retracted, push it back or wind it back in with a retraction tool as needed. Do not guess the piston type (push-in or wind-back): if it will not move, do not force it. This can break the actuator.
Stage 5 of 6 Reassembly 4 steps
- Place the caliper over the pads and tighten the mounting bolts. Approximate tightening torque is 25-40 N·m (18-30 lb-ft) for the caliper bolts and 50-100 N·m (37-74 lb-ft) for the bracket bolts (check exact values against the manufacturer's specifications). Tighten with a torque wrench.
- Reconnect the electric actuator connector if it was disconnected.
- Install the wheel, thread on the lug nuts by hand, lower the vehicle, and tighten the lug nuts in a crisscross pattern. Approximate lug nut torque is 100-130 N·m (74-96 lb-ft) (exact value per the manufacturer's specifications).
- Repeat everything on the other wheel of the same axle: pads are always replaced as a pair.
Stage 6 of 6 Checking 4 steps
- Exit EPB service mode with the scan tool and perform actuator calibration if required. Simply pressing the parking brake button is not enough for this.
- With the engine off, press the brake pedal several times until it feels firm. Check that there are no warning lights on the instrument panel and that the parking brake applies and releases.
- Check the brake fluid level in the reservoir: after the pistons are retracted, it may be above normal.
- Drive off at low speed and brake gently several times. For the first 200-300 km, avoid hard braking while the pads bed in.
Common mistakes and warnings
- This work involves the brake system, which is a safety matter
- If you lack experience or do not have a scan tool for EPB service mode, have the work done at a repair shop
- Do not drive if the pedal feels soft or sinks to the floor
- Always replace pads in pairs on an axle
- The torque values above are approximate
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Before you buy
German Turbo Engines vs. Chinese Ones: Which Lasts Longer? An Honest Look at Engine Life
Volkswagen 1.4 and 2.0 TSI, BMW N20 and Mercedes M274 versus Haval, Chery and Geely engines: lifespan benchmarks…
Read →
Brand stories
The History of Great Wall Motors
Great Wall Motors Ltd. has been one of China's largest automakers since 1995. It is essentially a holding company that…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →