Autopapyrus · Renault Talisman 1.5 dCi (2019)
https://autopapyrus.com/catalog/renault/talisman/guides/rear-brake-pad-replacement/
https://autopapyrus.com/catalog/renault/talisman/guides/rear-brake-pad-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Renault Talisman 1.5 dCi (2019): Rear Brake Pad Replacement
The Talisman 1.5 dCi K9K has disc brakes at the rear. The pads need replacing every 40,000-70,000 km (25,000-43,000 mi), depending on driving style. The procedure requires a jack and jack stands, so work carefully.
Parts
2| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Rear brake pads RenaultFind on Amazon → | AlternativesBoschFerodoTRW | |
| 02 | Rear brake rotorsif worn more than 2 mmFind on Amazon → | 432021878R |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
5
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
14 steps- Park the car on a level surface and engage the parking brake.
- Raise the car with the jack (if you are replacing both rear wheels' pads at the same time, lift both corners). Place jack stands under the frame rails.
- Remove the rear right wheel (17 mm wrench).
- Visually inspect the caliper (the brake assembly with two pistons on the side of the rotor). It should be positioned at the front of the rotor.
- Remove the two caliper bolts (17 mm): the upper and the lower.
- Swing the caliper aside (toward the center of the car) and take out the old pads.
- Wipe the rotor and the caliper mounting surface with a rag to remove dust.
- Retract both caliper pistons using a special C-clamp or tool. The pistons should go in by 5-10 mm to make room for the thicker new pads.
- Install the new pads (usually two thin plates) in the same way the old ones were seated. Check that they are not crooked.
- Reinstall the caliper and tighten the bolts to 20-30 N·m (15-22 lb-ft). Check the exact value in the K9K service manual.
- Install the wheel and tighten the lug nuts in a crisscross pattern.
- Repeat the procedure on the other rear wheel.
- Lower the car and press the brake pedal firmly several times until it stops. The brake pedal should feel firm.
- Drive slowly around a parking lot and make several gentle stops to bed in the pads.
Common mistakes and warnings
- Never work without jack stands – the jack can slip. — Do not reuse an old or damaged rotor – it is dangerous for braking at high speeds. — If the brake fluid in the reservoir is above the middle level, remove a little into a container before starting. When the pistons are pushed in, the fluid level rises and can overflow the reservoir. — Check the rotor thickness with a caliper. The minimum thickness for the Talisman K9K is approximately 8 mm (confirm in the technical documentation). If it is less, replace the rotor. — After the replacement, drive at moderate speeds for 50-100 km (30-60 mi) before braking hard or driving aggressively.
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Renault
Louis Renault (1877–1944) was interested in electricity and mechanics from an early age, and he was destined to become…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →