← Talisman Renault Talisman repair manuals →

Renault Talisman 1.5 dCi K9K (2019): DPF (Diesel Particulate Filter) Regeneration

The DPF (diesel particulate filter) on the 1.5 dCi K9K (3rd generation) clogs with soot after 60,000-80,000 km. Renault uses active regeneration, injecting fuel into the exhaust onto the hot catalyst. Forced regeneration with a scan tool is more effective and safer than hard driving.

DifficultyMedium Time30-60 minutesactive regeneration), plus 2-3 hours of engine idling or spirited driving Steps10

Part

№PartAlternatives
01 DPF (diesel particulate filter)only if replacement is neededFind on Amazon → AlternativesBoschMahle

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

10 steps
  1. Park the car in an open area, away from people and buildings. The engine may smoke and drone during the process.
  2. Connect a diagnostic scanner (Delphi, Autocom, Launch or similar) to the OBD-II port under the dashboard on the left side of the steering wheel.
  3. Open the menu: Renault → Talisman → Engine control (Moteur) → Live data and find the DPF soot load or DPF ash load parameter (in percent or grams).
  4. If the value is above 80%, regeneration is required. If it is above 95%, the filter is overloaded and may need to be removed and cleaned mechanically.
  5. Go to Actuation → DPF regeneration (Régénération FAP). The procedure activates fuel injection into the exhaust and raises the catalyst temperature to 600-700°C.
  6. Watch the progress on the scanner screen (there should be a filter load bar). The process takes 20-40 minutes depending on the load.
  7. During regeneration: — the exhaust pipe will be hot, do not touch it; — a burning smell and smoke are normal; — engine speed may change; — do NOT shut off the engine and do NOT disconnect the scanner.
  8. When regeneration is done, the scanner will display "Regeneration completed". Soot load should drop from 95% to 20-40%.
  9. Disconnect the scanner and let the car idle for 5 minutes to cool down the exhaust.
  10. Take an easy drive of 20-30 km at medium engine speeds (2000-3000 rpm) to fully restore the filter. Alternative (without a scanner): If you don't have a scanner, passive regeneration will kick in on its own: the DPF/FAP warning light on the instrument cluster will start flashing and the car will switch to a higher fuel consumption mode. You need to drive hard (60+ km/h, 2500+ rpm) for 2-3 hours. This is less effective and harder on the engine.

Common mistakes and warnings

  • Do not drive with the DPF light on for more than 100 km, or the filter will become overloaded and will need restorative service at a repair shop. — If regeneration starts while you are driving, keep driving calmly and do not accelerate hard. — If soot load stays stuck at 100% for several days and regeneration does not start automatically, the post-injection fuel injector or the exhaust pressure sensor may be faulty. Shop diagnostics are required. — The K9K DPF has a service life of about 180,000-200,000 km with proper oil maintenance and timely regeneration.
Spotted a mistake? Tell us →

Our articles

More articles →