← Freed

Honda Freed 1.5 (2021): Engine Oil and Oil Filter Change

The second-generation Freed with the L15B 1.5 engine takes 0W-20 oil, about 3.3 L (3.5 qt). The drain plug and filter are reachable from underneath at the front. The oil is changed together with the filter and a new drain plug washer.

DifficultyEasy Time40-60 minutes Steps13

Key figures

  • Oil capacity
    about 3.3 L (3.5 qt). This is how much to add after a filter change, so buy a 4 L (4.2 qt) container (step 10)
  • Oil viscosity
    0W-20. A full synthetic suitable for the L15B (step 10, parts)
  • Drain plug size
    17 mm. Use a socket or wrench (steps 4-5)
  • Level after filling
    between the dipstick marks, closer to the upper one. Check 5-10 minutes after shutting off the engine (step 12)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the oil cap, filler neck and dipstick are under the hood

Engine from above with the hood openi-VTEC1Oil filler cap2Oil filler neck3Oil dipstick4Engine cover5Intake manifoldEGR valveAlternatorTap to enlarge
  1. 1Oil filler cap: round, threaded, with a rubber ring. Unscrew it (a 14 wrench helps if tight) so the oil drains faster. Screw it back after filling.
  2. 2Oil filler neck: the opening in the black well, left and below the engine cover. Pour about 3.3 L of 0W-20 oil through it with a funnel.
  3. 3Dipstick: orange handle, thin blade goes down along the engine cover edge. Check the level 5-10 minutes after stopping: between the marks, closer to the upper one.
  4. 4Engine cover: ribbed, with the i-VTEC badge. A landmark: the filler cap sits on it.
  5. 5Intake manifold: grey, with curved runners to the right of the cover. A landmark, do not touch.

Parts

3
№PartAlternatives
01 Full synthetic engine oil 0W-20, API SN/SP, ILSAC GF-5/GF-6Aabout 3.3 L (3.5 qt); 4 L (4.2 qt) containerFind on Amazon →
02 Oil filter for L15B 1.5 engineFind on Amazon → AlternativesVicMasumaFQ
03 Drain plug washer (copper or aluminum)newFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Step by step

13 steps
  1. Warm up the engine for 5-10 minutes so the oil thins out. Park the car on level ground, shut off the engine, and set the parking brake. Wait 5-10 minutes so some of the oil drains down into the oil pan.
  2. Open the hood and unscrew the oil filler cap (a 14 mm wrench can help if the cap is tight). This lets the oil drain faster.
  3. Get under the front of the car. The filter and drain plug are visible from below. If your car has an engine skid plate (under-engine shield), remove it by its fasteners.
  4. Place the drain pan under the plug. Use a 17 mm wrench to loosen the drain plug slightly, then loosen the oil filter slightly in the same way with the filter wrench.
  5. Unscrew the plug by hand, holding on to it so it doesn't drop into the pan. The oil is hot, so wear gloves. Let the oil drain until the stream turns into occasional drips.
  6. When the oil is down to drips, unscrew the filter. Don't turn it upside down, as it still holds hot oil. Hold the pan or a rag underneath.
  7. Wipe the filter mounting surface and the drain plug threads. Remove the old drain plug washer (pry it off with a flat-blade screwdriver) and fit the new one.
  8. Pour a little fresh oil into the new filter and lubricate its rubber gasket with it. Spin the filter on by hand until the gasket touches, then tighten it a bit more without excessive force. For the exact filter tightening torque, see the filter itself or the service manual.
  9. Install the drain plug with the new washer and tighten it with a torque wrench. A typical torque for Honda drain plugs is 35-45 N·m (26-33 lb-ft). Check the exact value for the L15B against the manufacturer's service manual. Don't overtighten: threads in an aluminum oil pan strip easily.
  10. Pour in about 3.3 L (3.5 qt) of 0W-20 oil through a funnel. Screw the filler cap back on.
  11. Start the engine for 1-2 minutes. Make sure the oil pressure warning light goes out and that there are no leaks at the filter or the plug.
  12. Shut off the engine, wait 5-10 minutes, and check the level with the dipstick on level ground. The level should be between the marks, closer to the upper one. If needed, top up in small amounts.
  13. Take the used oil and filter to a collection point for disposal. If the oil change reminder is enabled, reset it in the on-board computer following the owner's manual.

Common mistakes and warnings

  • Work only on reliable jack stands or a lift
  • Never get under a car supported only by a jack
  • Don't fill the oil above the upper dipstick mark, and don't use any viscosity other than 0W-20 unless the service manual allows it
  • Follow the maintenance schedule in the service book for the change interval
  • With frequent short trips, heavy traffic, or severe service, it is better to change the oil more often
  • Always use a new drain plug washer
Spotted a mistake? Tell us →

Our articles

More articles →