https://autopapyrus.com/catalog/hyundai/tucson/guides/parking-brake-adjustment/
Hyundai Tucson (3rd generation, TL): Parking Brake Adjustment
On the Tucson TL, the lever-operated parking brake works on small shoes inside the rear brake rotors (a "drum-in-hat" design). Adjustment is done in two stages: first the shoe clearance through the access hole in the rotor, then the lever travel with the cable adjusting nut. If your vehicle has an electric parking brake (a button instead of a lever), you don't need to adjust the cable. The shoe clearance is set the same way, but leave the electronic part to a repair shop.
Key figures
- Parking brake lever travel5-6 clicks at a force of about 20 kgf (196 N). This is the normal range after adjustment, checked in steps 9-10
- Adjuster gear back-off4-5 teeth. This is how far you turn the screwdriver back after the gear stops, so the shoes don't rub on the rotor (step 5)
- Lever pre-cycling3 times. Done before adjusting the cable nut to take up the slack (step 8)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the disc hole and parking brake lever are
- 1Service hole in the rear brake disc: pull the plug out of it.
- 2Screwdriver: through the hole turn the adjuster gear down until it stops, then back 4-5 teeth.
- 3Shoe adjuster gear inside the hole: turn it down until the disc stops turning.
- 4Parking brake lever: before adjusting the cable nut, pull it fully up and release three times.
- 5Console trim around the lever: remove it to reach the cable adjusting nut, refit after adjusting.
- 6Wheel studs: when refitting the wheel, put the nuts on and tighten them in a cross pattern.
Parts
2| № | Part | Genuine part no. |
|---|---|---|
| 01 | Rear parking brake shoesif heavily wornFind on Amazon → | 58305-D3A00 |
| 02 | Parking brake cableif heavily wornFind on Amazon → | 59760-D3000 |
| 59770-D3000 | ||
| 59750-D3100 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
6
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more.
See manuals →
Step by step
12 steps- Park the vehicle on level ground, chock the front wheels, and loosen the lug nuts on the rear wheel. The parking brake lever must be released (down).
- Raise the rear of the vehicle, set it on secure jack stands, and remove the rear wheel.
- Remove the plug from the rear brake rotor (the access hole opposite the adjuster gear).
- Through the hole, use a screwdriver to turn the adjuster gear downward until the rotor no longer turns (the shoes are against the drum surface).
- Then turn the gear back the opposite way by 4-5 teeth (service manuals for different generations give 4-5 teeth): the rotor should spin freely without dragging.
- Install the plug and the wheel. Repeat steps 2-6 on the other rear wheel. Tighten the lug nuts in a crisscross pattern to the manufacturer's specified torque (a reference value for this class of vehicle is 100-110 N·m (74-81 lb-ft)).
- Lower the vehicle. Remove the floor console trim around the parking brake lever to access the cable adjusting nut.
- Pull the lever fully and release it three times to take up the slack in the cable.
- Turn the cable adjusting nut until the lever travel is 5-6 clicks at a lever force of about 20 kgf (196 N).
- Release the lever fully: the wheels should spin freely and the shoes should not drag. If there is drag, loosen the nut by half a turn and check again.
- There should be no gap left between the adjusting nut and the stud, and the brake should not stick.
- Install the console trim. Check the holding ability: the parking brake should hold the vehicle securely on a reasonably steep slope.
Common mistakes and warnings
- The brake system is safety-critical: if you have no experience working on suspension and brakes, have a repair shop do the adjustment
- Always adjust the cable only after adjusting the shoe clearance
- Work only on a vehicle supported by jack stands, never under a jack alone
- If after adjustment the lever still travels more than 6 clicks or the vehicle does not hold, the shoes or cable are worn and need replacement
- The torque values and tooth counts given here are approximate, so verify the exact values against the manufacturer's service manual
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Hyundai
Hyundai Motor Company, whose name means "modernity" in Korean, is South Korea's largest automaker and one of the top…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →