← Korando

KGM Korando (2025): Low Beam Bulb Replacement

This guide is for versions with halogen headlights, where the low beam is a removable bulb at the back of the headlight. The procedure is typical for H7 headlights. On versions with LED or xenon (D1S) headlights, the bulb is not a replaceable consumable. That work is for a repair shop, because xenon systems run on high voltage. If the protective cover does not give you access, remove the headlight assembly, as on similar models.

DifficultyMedium Time20-40 minutes per headlight Steps20

Part

№PartAlternatives
01 halogen low beam bulb1 per headlightFind on Amazon → AlternativesOsramPhilipsBosch

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

4
  • gloves (cotton or nitrile) Amazon →
  • Phillips screwdriver and 10 mm socket (in case you need to remove protective covers or the air duct) Amazon →
  • flat plastic pry tool Amazon →
  • flashlight Amazon →

Step by step

20 steps · 4 stages
Stage 1 of 4 Preparation 4 steps
  1. Park the vehicle on level ground, turn off the engine, switch off the lights and remove the key. Wait 10-15 minutes for the bulb to cool.
  2. Open the hood and locate the back of the headlight you are working on. Check what blocks access: the reservoir, the air duct, clips.
  3. Identify which bulb in the headlight is which. Typically these are the high beam, the low beam, and the parking light or turn signal, each in its own socket. The low beam is usually the bulb with the largest base area. If you are not sure, turn on the low beam and use the light to identify the socket.
  4. Put on gloves. Do not touch the glass of the bulb with bare fingers: skin oil shortens the bulb's life and causes it to burn out.
Stage 2 of 4 Access and removal 5 steps
  1. If access is blocked by an air duct or hose, loosen the clamp or unclip the clips and carefully move the part aside. If a reservoir is in the way, move it aside without disconnecting the hoses. Do not strip or overtighten the fasteners.
  2. Remove the protective rubber or plastic cover from the back of the headlight. Open it by turning it counterclockwise or by pulling the tab.
  3. Disconnect the connector from the bulb base. Press the locking tab and pull the connector toward you. Pull on the connector, not on the wires.
  4. Release the bulb from its retainer. In headlights with an H7 bulb this is a spring clip: press the end of the clip and swing it aside. In other designs, the base is turned a quarter turn counterclockwise.
  5. Pull the bulb straight out of the reflector without tilting it. Note the position of the tabs on the base.
Stage 3 of 4 Installation 5 steps
  1. Compare the new bulb with the old one: type, 12 V, 55 W, base shape.
  2. Hold the new bulb only by its base. If you touched the glass, wipe the bulb with rubbing alcohol and let it dry.
  3. Insert the bulb into the reflector so that the tabs line up with the slots. It should seat without force, not at a crooked angle. A wrong angle degrades the beam, and after correct installation there should be no tilt.
  4. Secure the bulb with the clip or by turning the base all the way, and make sure it does not wobble.
  5. Plug in the connector until it clicks.
Stage 4 of 4 Reassembly and check 6 steps
  1. Do not put the cover back right away. Turn on the low beam and check that the bulb lights up.
  2. Turn off the lights and install the protective cover. It must seat all the way around: a crooked cover lets in water and dust, and the headlight fogs up.
  3. Put the air duct, reservoir and clips back in place. If you removed any fasteners, tighten them without overtightening; no torque specification is needed in this case.
  4. If you replaced only one bulb, consider replacing the other as well: bulbs have a similar service life, and a new one and an old one will differ in brightness. Replace them as a pair.
  5. Check the beam pattern against a wall from a distance of about 5-10 m. The left and right headlights should produce the same pattern, and the light/shadow cutoff should be level. If a bulb is seated incorrectly or the pattern is skewed, repeat the installation.
  6. If the beam aims higher or lower than it should, have the headlights adjusted on a beam setter at a repair shop. This is usually not needed after a bulb replacement if the bulb is seated correctly.

Common mistakes and warnings

  • Do not install LED H7 bulbs in place of halogen ones without certification: in halogen reflector optics they dazzle oncoming drivers, and the control unit may throw a lighting circuit fault
  • Do not touch the bulb with your fingers
  • Leave work on xenon (D1S) and LED headlights to a repair shop because of the high voltage
Spotted a mistake? Tell us →