Autopapyrus · KGM Korando (4th generation)
https://autopapyrus.com/catalog/kgm/korando/guides/cabin-air-filter-replacement/
https://autopapyrus.com/catalog/kgm/korando/guides/cabin-air-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
KGM Korando (4th generation): Cabin Air Filter Replacement
The cabin air filter cleans the air that flows from the heater and A/C into the cabin. Replace it about once a year or every 15,000 km, and more often in dusty conditions and city driving. The filter is located behind the glove box on the passenger side. Check the exact glove box removal procedure for this generation in your owner's manual.
Key figures
- Replacement intervalafter this mileage the filter becomes clogged with dust and the airflow weakens (intro and step 5)once a year or 15,000 km
- New filter sizecheck against the packaging when buying so the filter fits in the housing without gaps (part)about 202 × 200 × 34 mm
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: what the new cabin filter looks like, where the arrow points and its size
Tap to enlarge
- 1New cabin filter: goes in place of the old one behind the glovebox. Check the size against the package.
- 2Arrow on the frame (AIR FLOW): airflow direction. Install the new filter with the arrow pointing the same way as the old one.
- 3New filter size is about 202 × 200 × 34 mm: check the package so it fits without gaps.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Cabin (dust) air filter, approx. 202 × 200 × 34 mmcharcoal version available (traps odors better)Find on Amazon → | AlternativesFiltronMannBosch |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
3Step by step
10 steps- Park the vehicle on level ground, turn off the engine and remove the key. Move the passenger seat back for easier access.
- Open the glove box and take everything out of it.
- Release the glove box so that it swings down. Usually this is done by squeezing the sides of the glove box inward and freeing the stops on both sides, and disconnecting the damper (arm), if there is one. If the glove box is held by screws, remove them with a screwdriver and carefully unclip the retainers without using excessive force.
- Behind the glove box, find the rectangular filter cover. Press the cover clips (latches), usually two of them, and remove the cover.
- Pull out the old filter and note how it was installed: the arrow on the frame shows the direction of airflow. Slide the old filter out slowly so debris does not fall into the air duct.
- Remove leaves, dust and debris from the filter housing with a vacuum cleaner or a dry rag. Do not use cleaning agents or water.
- Insert the new filter so that the arrow on the frame points in the same direction as on the old one. As a rule, the airflow goes downward, but follow the arrow on the old filter. The filter must sit flat, with no misalignment or gaps.
- Put the cover back on until the clips click into place.
- Reinstall the glove box: engage the stops, reconnect the damper, and secure the retainers or screws. Torque specs are not needed; just tighten the screws snug without force so you do not strip the plastic.
- Turn the ignition on and set the heater fan to medium speed. Check that the air flows normally and there is no unusual noise or whistling.
Common mistakes and warnings
- A filter installed with the arrow in the wrong direction cleans the air less effectively and may be noisy
- Do not break the plastic clips of the glove box and cover: they are brittle, especially in the cold, so warm up the cabin first
- If the airflow is weaker after replacement, the filter is installed crooked or the cover is not fully seated
- Check the exact glove box removal procedure for your version in the owner's manual