← K5

Kia K5 (1st generation, DL3): Front Wiper Blade Replacement

The front K5 wiper blades attach to the wiper arms with a latch, so no tools are needed to replace them. Replace them when they leave streaks, squeak, or skip across the glass. This is usually every 6-12 months, and more often in strong sun. The K5 is a sedan, so it has no rear wiper.

DifficultyEasy Time5-10 minutes Steps9 ToolsNone needed (for glass protection, use a folded towel or a piece of cardboard)

Key figures

  • Driver-side blade length
    26 in (about 650 mm). Use this size when buying the blade for steps 2-5.
  • Passenger-side blade length
    16 in (about 400 mm). Use this size when buying the blade for step 8. The sizes are different, so a set of two identical blades won't fit.

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: wiper arm, clip and blade when replacing wipers

Wipers seen from inside the car: arms lifted off the glassLift the arm all the way4Driver blade 26″5Passenger blade 16″1Cardboard under the arm2Wiper arm (lever)Close-up: blade attachmentLiftPull the blade down along the arm3Clip (lock)View from inside: driver on the left, passenger on the rightTap to enlarge
  1. 1Put a folded towel or cardboard on the glass under the arm so it can't hit the glass.
  2. 2Wiper arm: metal lever. Lift it off the glass until it locks and hold it.
  3. 3Clip where the arm enters the middle of the blade. Lift it.
  4. 4Driver blade, 26 in (about 650 mm): pull down along the arm and remove; push the new one on until it clicks.
  5. 5Passenger blade, 16 in (about 400 mm): shorter than the driver one, replaced the same way. Don't mix up sides.

Parts

3
№PartGenuine part no.Alternatives
01 Front wiper blade, driver side, 26 in (about 650 mm)1 pc; sold as a set with the passenger blade, different lengthsFind on Amazon → 98350-3X000 AlternativesBoschValeoDensoTrico
98350-3S300
02 Front wiper blade, passenger side, 16 in (about 400 mm)1 pc; sold as a set with the driver blade, different lengthsFind on Amazon → AlternativesBoschValeoDensoTrico
03 Wiper blade replacement insertonly if replacing the rubber; separate inserts for driver side (26 in) and passenger side (16 in)Find on Amazon → AlternativesBoschValeoDensoTrico

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Step by step

9 steps
  1. Turn off the engine and park the car. Place a folded towel or a piece of cardboard on the glass under the wiper arm. If the arm slips, it won't hit the glass.
  2. Take the driver-side wiper arm and lift it off the glass until it locks in the upright position. Hold it with your hand.
  3. Lift the latch (clip) where the blade attaches to the arm.
  4. Pull the blade down along the arm and remove it.
  5. Compare the new blade with the old one: the length, shape, and type of attachment must match. Slide the new blade onto the arm and pull it down until the latch clicks.
  6. Gently pull the blade toward you and make sure it is held firmly.
  7. Carefully lower the arm onto the glass. Don't let go of it, because it can slam into the glass and cause a chip or crack.
  8. Repeat steps 2-7 for the passenger-side blade (16 in). Don't mix up the sides: the long blade goes on the driver side.
  9. Wipe the glass to remove dust and film. Wet the glass with washer fluid, turn on the wipers, and check that the blades don't leave streaks and don't hit each other or the windshield pillar.

Common mistakes and warnings

  • Don't let the wiper arm drop onto the glass unsupported, or you can crack or scratch the windshield
  • Don't install blades longer than the factory size
  • A 26 in blade on the passenger side will hit the driver-side blade, and a 16 in blade on the driver side will leave an unwiped strip
  • Don't run the wipers on dry glass or while the blades are removed
  • If the arm is bent or doesn't press the blade down well, replace the arm separately
  • Torque specs are not needed, because the attachment has no threads
Spotted a mistake? Tell us →