← Model 3

Tesla Model 3 (2021): Wiper Blade Replacement

Replace the Model 3 wiper blades at least once a year. Worn blades clear the glass less effectively in the rain. The replacement is done through the touchscreen: the wipers move to the service position, and you remove the blade by pressing the lock tab. This guide covers the windshield wiper blades.

DifficultyEasy Time10-15 minutes Steps12

Key figures

  • How often to replace the bladesso the glass clears well in the rain (step 1)
    at least once a year

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the wiper blade latch is and how to remove the blade

View of the driver's blade when standing at the hoodRemove: slide along the arm1Wiper arm2Latch: press3Blade with adapter4Towel under the arm5WindshieldHoodTap to enlarge
  1. 1Wiper arm: lift it only as high as needed and hold it by hand, it does not lock up.
  2. 2Latch on the arm: press the square latch and slide the blade along the arm.
  3. 3Blade with its adapter: slide the new blade in until it clicks, the latch goes into the small hole.
  4. 4Soft towel: lay it on the glass under the arm so it cannot scratch or crack the glass.
  5. 5Windshield: after the swap wipe it with a soft cloth, warm water and soap.

Parts

2
№PartAlternatives
01 Windshield wiper blade, frameless or with a connector for the Model 3 mount, 650 mm (driver side)1 pcFind on Amazon → AlternativesBoschValeoDenso
02 Windshield wiper blade, frameless or with a connector for the Model 3 mount, 475 mm (passenger side)1 pcFind on Amazon → AlternativesBoschValeoDenso

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

2

Step by step

12 steps
  1. Park the car, shift into P (Park), and turn the wipers off. Wiper service mode can only be turned on when the wipers are off.
  2. On the touchscreen, open Controls, then Service, and turn on Wiper Service Mode. The name of this item depends on the software version. The wipers will move to the replacement position.
  3. Go to the front of the car at the hood. Place a folded soft rag on the glass under the arm, so that an accidental drop of the arm does not scratch or crack the glass.
  4. Lift the driver-side wiper arm just high enough to reach the blade. The arm does not lock in the raised position, so hold it with your hand. Do not lift the arm past its range of travel: damage from this is not covered by the warranty.
  5. Press the rectangular lock tab on the arm and slide the old blade along the arm to remove it.
  6. Compare the length of the new blade with the old one. Then line up the new blade with the arm and slide it in toward the hooked end until it clicks. The lock tab should seat in the small hole.
  7. Pull on the blade by hand to make sure it does not slip out.
  8. Slowly lower the arm onto the glass. Do not let go of it, or it will slap against the glass.
  9. Repeat steps 4-8 for the passenger-side blade, which is shorter.
  10. Wipe the glass with a soft rag, warm water and soap without detergent additives, then rinse with clean water. The glass is clean when water does not bead up on it.
  11. Get in the car and turn off Wiper Service Mode in the same menu. The wipers will also return to the operating position when you shift out of P.
  12. Run the washer and wipers for a couple of cycles. Check for streaks and squeaking, and make sure the blades do not hit the pillars or each other as they sweep.

Common mistakes and warnings

  • Install only blades identical to the factory ones
  • Unsuitable blades can damage the wiper drive and affect the rain sensor
  • To clean the glass and rubber, use only products approved for automotive glass
  • Replace an old blade with cracks or tears right away so it does not scratch the glass
  • No fasteners are removed during this replacement, so no torque specs are needed
Spotted a mistake? Tell us →

Our articles

More articles →