← Model 3

Tesla Model 3 (2021): Jacking Up and Rotating the Wheels

On the Model 3, lift the car only at the four body jacking points: one right behind each front wheel and one right in front of each rear wheel. Do not lift by the battery pack or the side sill rails. Loosen the lug nuts before lifting, and tighten them in a star pattern with a torque wrench once the car is back on the ground. This guide covers rotating the wheels using a jack and jack stands.

DifficultyEasy Time45-60 minutes Steps22

Key figures

  • Lug nut tightening torqueset this on the torque wrench in step 18 and tighten the nuts in a star pattern; less is dangerous (the wheel may come off), more will strip the threads
    175 N·m (129 lb-ft)
  • Lug nut sizeyou need the 21 mm socket both for loosening the nuts in step 6 and for tightening in step 18
    21 mm
  • Re-check of tightnessgo over the nuts again with the wrench at 175 N·m (129 lb-ft), step 22
    after 50-100 miles (about 80-160 km) of driving
  • Number of jacking pointsone behind each front wheel and one in front of each rear wheel, steps 7-8; never place the jack under the battery pack
    4

Check these values against the manufacturer’s specification for your vehicle before you start.

Part

№Part
01 Copper or ceramic anti-seize for hub mounting surfaceoptionalFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

9
  • Low-profile floor jack (1.5-3 ton is fine) Amazon →
  • two jack stands Amazon →
  • rubber or polyurethane jack pad (puck) with a raised tab that fits the jacking point hole Amazon →
  • 21 mm socket Amazon →
  • breaker bar or lug wrench for loosening the nuts Amazon →
  • torque wrench (up to 200 N·m (148 lb-ft)) Amazon →
  • wheel chocks Amazon →
  • tire inflator and pressure gauge. If the wheels have decorative lug nut caps Amazon →
  • you will need a cap removal tool Amazon →

Step by step

22 steps · 5 stages
Stage 1 of 5 Preparation 5 steps
  1. Park the car on a level, hard surface (asphalt or concrete), select Park (P), and set the parking brake.
  2. Disconnect the charging cable. Do not lift the car with the cable connected, even if it is not charging.
  3. Place wheel chocks under the wheels that stay on the ground.
  4. If the lug nuts have caps, remove them with a cap removal tool. If wheel covers are installed, remove them.
  5. Measure and record the tire pressures. Compare the cold tire readings with the data on the placard in the driver's door jamb.
Stage 2 of 5 Loosening the nuts and lifting 6 steps
  1. While the wheels are still on the ground, loosen the lug nuts on every wheel you will remove by about half a turn. Use a 21 mm socket. Do not remove them completely.
  2. Locate the jacking point. It is on the body at the outer edge of the battery pack, right behind the front wheel or right in front of the rear wheel, and is marked by a round hole. Check the exact location against the sticker or diagram under the car, as positions may differ slightly.
  3. Insert the jack pad into the jacking point so the tab seats in the hole and the pad does not wobble. Do not place the jack head under the battery pack or the side rails, as this can damage the battery. Lifting at any point other than the specified ones is not covered by the warranty.
  4. Position the jack so the head with the pad just touches the jacking point, then smoothly raise the car until the wheel is off the ground.
  5. Immediately place a jack stand under the adjacent jacking point or another solid area near the jack (per the Tesla diagram). Lower the car onto the stand. Never work under a car that is supported only by a jack.
  6. If you are putting the whole car on stands, repeat steps 7-10 for the other wheels. For a simple rotation, it is easier to lift one axle at a time.
Stage 3 of 5 Removing and rotating the wheels 4 steps
  1. Remove all the lug nuts and take off the wheel. Support it so you do not damage the brake rotor or the stud threads.
  2. Inspect the tires for cuts, bulges and uneven wear, and check the brake rotors and pads for thickness and wear. Clean dirt and rust off the hub mounting surface with a brush.
  3. Choose a rotation pattern. If the front and rear wheels and tires are the same size, swap them between axles. If the front and rear sizes differ (for example, on trims with staggered wheels) or the tires are directional, you can only swap wheels side to side on the same axle or rotate them on their own axle. See the Tesla maintenance schedule for the recommended rotation interval.
  4. Mount the wheel on the hub, align the holes with the studs, and thread the lug nuts on by hand.
Stage 4 of 5 Tightening and lowering 4 steps
  1. Hand-tighten all the lug nuts on the wheel in a star (criss-cross) pattern in two passes so the wheel seats evenly.
  2. Raise the car with the jack, remove the jack stand, and smoothly lower the car until the tires touch the ground.
  3. Do the final tightening with a torque wrench and a 21 mm socket to 175 N·m (129 lb-ft) in a star (criss-cross) pattern. Do this with the wheel on the ground.
  4. Repeat steps 7-18 for the remaining wheels you are rotating.
Stage 5 of 5 Inspection 3 steps
  1. Adjust the tire pressures to the specification on the door jamb placard, and refit the lug nut caps and wheel covers if you removed them.
  2. Turn on the car and check for any tire pressure warnings. If necessary, check the tire pressure sensors (TPMS) in the car's menu.
  3. Drive a few kilometers and listen for any wobble or knocking. After 50-100 miles (about 80-160 km), recheck the lug nut torque at 175 N·m (129 lb-ft).

Common mistakes and warnings

  • Lift the car only at the four marked body points
  • Lifting by the battery pack or the side rails can damage the battery and is not covered by the warranty
  • Never get under a car that is supported only by a jack, and never lift it with the charging cable connected
  • Tighten the lug nuts with a torque wrench, not an impact wrench at full power
  • Under-tightened nuts can lead to losing a wheel, and over-tightened nuts strip the stud threads and distort the wheel
  • If you have no experience using a jack, have a shop lift the car on a hoist or have a tire shop do it, and tell the technician about the Model 3 jacking points
Spotted a mistake? Tell us →

Our articles

More articles →