Autopapyrus · Tesla Model 3 (2021)
https://autopapyrus.com/catalog/tesla/model-3/guides/getting-into-the-car-with-a-dead-low-voltage-battery/
https://autopapyrus.com/catalog/tesla/model-3/guides/getting-into-the-car-with-a-dead-low-voltage-battery/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model 3 (2021): Getting into the Car with a Dead Low-Voltage Battery
When the low-voltage 12 V battery is dead, the door handle buttons, touchscreen and app don't work. You can get in through the mechanical release on the front door, and the hood opens when you supply external 12 V to the wires under the tow eye cover in the front bumper. This guide covers getting into the car and opening the hood (front trunk), followed by jump-powering the car.
Key figures
- External source voltage12 V. A portable jump starter or another vehicle's battery works, connected to the wires under the cover in the bumper (steps 9-10)
- What to connect first and disconnect firstconnect the red positive first, and begin disconnecting with the black negative, which lowers the risk of a short circuit (steps 9, 11, 16)
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part |
|---|---|
| 01 | 12 V battery for Model 3 (lead-acid or lithium)if worn outFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
2Step by step
19 steps · 4 stagesStage 1 of 4 Getting inside 5 steps
- Prepare an external 12 V source: a charged portable jump starter or another vehicle's battery. Never use the Model 3 itself to jump-start other vehicles, as it can be damaged.
- Try unlocking the car with the key card: hold it against the driver's door pillar. If the 12 V battery is completely dead, this may not work, so go to step 3.
- Pull the door handle by its edge and open the front door by pulling up the mechanical release located in front of the window switches. The electric button on the upper part of the inside handle doesn't work without power.
- The mechanical release is only on the front doors. If you need to get inside, enter through a front door, because the rear doors can't be opened from the inside without power.
- Use this mechanical release only when there is no power. When power is available, use the button on the inside handle.
Stage 2 of 4 Opening the hood through the tow eye cover 6 steps
- Find the tow eye cover on the front bumper.
- Press on the upper right part of the cover's edge until it pivots inward, then carefully pull the raised edge toward you and remove the cover.
- Pull two wires out of the opening: red (positive) and black (negative). The cover is electrically connected to the black negative terminal, so don't touch the positive terminal with the cover or the wires.
- Connect the source's red positive lead to the red positive terminal, then the source's black negative lead to the black negative terminal.
- Turn on the external source: the hood latches release right away. These wires do not charge the 12 V battery. They only open the hood.
- Disconnect the leads, starting with the black negative. Open the hood by lifting it.
Stage 3 of 4 Powering the battery and restoring the car to working condition 6 steps
- If you need to bring the car back to life (screen, locks, ready to drive), remove the service panel under the hood by pulling it up until the clips release.
- Remove the cabin air intake panel, also by pulling it up until the clips release.
- Connect the external source's red positive to the red positive terminal of the 12 V battery, and the black negative to the black negative terminal. Don't let the positive lead touch any metal parts, such as the battery mounting bracket, and don't let the leads touch each other.
- Turn on the external source and touch the touchscreen to wake it up. The screen may need a few minutes to build up enough power.
- When external power is no longer needed, disconnect both leads, starting with the black negative.
- Install the air intake panel by pressing it down until it locks, then install the service panel the same way. Close the hood.
Stage 4 of 4 Check 2 steps
- Turn on the car and make sure the screen works and the doors and locks respond to the key card and the app.
- If the battery went dead for no obvious reason or the problem keeps happening, check its condition and replace it if it is worn out: its service life drops after repeated deep discharges.
Common mistakes and warnings
- Don't climb into the front trunk, and don't close it with a person inside
- Don't let the leads short out or the positive touch the car's metal body
- The rear tow eye cover is intended for transport and is not suitable for jump-powering
- If you have no experience with automotive electrical systems, contact a repair shop
- Don't touch the high-voltage battery or the orange high-voltage cables
Spotted a mistake? Tell us →
Our articles
Test drives
Tesla Model 3 Review
Electric cars from the American company Tesla are gaining popularity around the world and sell by the thousands. Not…
Read →
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →