← Model 3

Tesla Model 3 (2021): Low-Voltage (12 V) Battery Replacement

On a 2021 Model 3, the low-voltage battery is a lead-acid type located under the rear hood cover (in the front trunk). It powers the electronics and door operation, and its service life is usually about 3-5 years. Replacement must follow a strict order: before disconnecting the 12 V, you need to open the doors and lower the windows, otherwise the doors may lock and the electronics may be damaged. This guide covers the lead-acid battery (2021 model year).

DifficultyMedium Time1-1.5 hours Steps31

Key figures

  • Terminal tightening torque (positive and negative)
    6 N·m (53 lb-in). Use a torque wrench with a 10 mm deep socket, steps 22 and 26. Overtightening will damage the terminal.
  • Battery hold-down bar tightening torque
    5 N·m (44 lb-in), step 21. Otherwise the battery will move around or the bar will crack.
  • New battery voltage
    above 12.6 V. Check with a multimeter before installation, step 2. Do not install below 12.4 V.
  • Pause after turning off climate control
    at least 30 seconds, step 4, before disconnecting power.
  • Wait time if the bus still reads above 10 V after disconnecting
    2 minutes, step 14, then measure again.

Check these values against the manufacturer’s specification for your vehicle before you start.

Part

№PartAlternatives
01 12 V lead-acid (AGM) low-voltage battery for Model 3 built before 2022same type and size as the one installed; the 12 V lithium-ion battery (2022 onward) is not a fitFind on Amazon → AlternativesClariosVartaAtlasBX

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6

Step by step

31 steps · 5 stages
Stage 1 of 5 Preparation 6 steps
  1. Check the battery type: Controls > Software > Additional Vehicle Information. The lead-acid (AGM) version is described below.
  2. Check the new battery with a multimeter: the open-circuit voltage should be above 12.6 V. If it is 12.4-12.6 V, charge it. If it is below 12.4 V, do not install that battery.
  3. Unplug the charging cable from the vehicle. Put the vehicle in Park.
  4. On the touchscreen, turn off climate control and wait at least 30 seconds. Do not move the windows for at least 1 minute before disconnecting the 12 V.
  5. Open all the doors and lower all the windows. Closed windows can crack when a door is opened, and closed doors may lock after power is disconnected.
  6. Open the left and right rear doors and thread a clean cloth halfway through the latch striker of each door, so the latch cannot engage and the vehicle cannot be locked by accident.
Stage 2 of 5 Access and power disconnection 8 steps
  1. Remove the lower rear seat cushion (second row). This step is needed on vehicles in the original configuration; later variants with a heat pump do not have it.
  2. Open the hood (front trunk). Release the 12 clips and remove the rear hood cover (apron). No tools are needed, only the clips.
  3. On the screen: Controls > Safety > Power Off. The screen and systems will go dark.
  4. Loosen the nut on the negative terminal (10 mm deep socket) and remove the negative cable from the terminal. The negative is disconnected first.
  5. If there is a First Responder Loop near the right side of the battery: slide the red lock back, press the black tab, and disconnect the connector. Only after the negative is disconnected.
  6. Measure the voltage at the battery terminals. If the reading is below 10 V or above 14 V, the multimeter cannot be used for this procedure.
  7. If a foam cover is installed on the right side of the electronics bay, remove it. Disconnect the high-voltage controller harness connector (the HV battery contactors open with a click) and fit the special protective cap (logic connector cap) on its connector.
  8. Measure the voltage on the low-voltage bus in the bay: below 1 V means you can continue. Above 10 V means wait 2 minutes and measure again. If it is still above 10 V, stop work and contact Tesla service.
Stage 3 of 5 Old battery removal 5 steps
  1. Remove the upper cabin air intake duct.
  2. Remove the protective cover from the positive terminal. Loosen the positive cable nut (10 mm deep socket) and remove the cable from the battery.
  3. Remove the battery hold-down bar (strap). On vehicles with a rear hook, remove the bolt holding the upper bracket and lift the bar off the hook. On vehicles with a front hook, loosen the upper bracket nut, press the bar down and slide it to the right to release it from the front and rear hooks.
  4. Disconnect the (drain) hose from the left side of the battery and lift the battery out. It is heavy, so lift it carefully.
  5. Write the last 6 digits of the VIN on the old battery with a marker (for warranty return and recycling).
Stage 4 of 5 New battery installation 4 steps
  1. Set the new battery in place and connect the hose to its left side.
  2. Install the hold-down bar and tighten the bracket nut/bolt to 5 N·m (44 lb-in).
  3. Put the positive cable on the terminal and tighten the nut to 6 N·m (53 lb-in). Close the positive terminal protective cover.
  4. Install the cabin air intake duct.
Stage 5 of 5 Power reconnection and check 8 steps
  1. Remove the cap from the high-voltage controller connector and plug the harness back in. Install the foam cover.
  2. If there is a First Responder Loop, connect it and slide the red lock forward until it latches. Do not connect the negative terminal before this.
  3. Put the negative cable on the terminal, press it down firmly and tighten the nut to 6 N·m (53 lb-in).
  4. Install the rear seat cushion (if you removed it) and the rear hood cover (12 clips). If there is a First Responder Loop, its sticker must not be visible after the cover is installed.
  5. Press the brake pedal to power on the vehicle. Wait for the screen to load.
  6. Remove the cloths from the rear door latch strikers. Return the windows, seats, climate control and charging to their previous state. Close all the doors.
  7. If you changed the battery brand (Clarios/Varta to AtlasBX or the other way around), you need to change the battery type in the vehicle settings using service mode (software 2023.32 or newer and Tesla service equipment are required). If the brand has not changed, this step is not needed.
  8. Check operation: screen startup, locks, windows, lights, and no errors in the notifications. Take the old battery to a battery recycling drop-off.

Common mistakes and warnings

  • This procedure disconnects only the 12 V and does not guarantee that there is no high voltage in components (A/C compressor, inverters, heater)
  • If you are not experienced with electric vehicles, leave the work to a repair shop
  • Before working on HV components, a separate high-voltage shutdown procedure and 1000 V rated gloves are required
  • The order of the steps matters: breaking the sequence can damage the vehicle's computer
  • Do not disconnect the 12 V while the climate control is running, and do not change the window positions shortly before disconnecting
  • Before you start, make sure the battery is not overheated
Spotted a mistake? Tell us →

Our articles

More articles →