Autopapyrus · Tesla Model 3 (2021)
https://autopapyrus.com/catalog/tesla/model-3/guides/cleaning-and-lubricating-the-brake-calipers/
https://autopapyrus.com/catalog/tesla/model-3/guides/cleaning-and-lubricating-the-brake-calipers/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model 3 (2021): Cleaning and Lubricating the Brake Calipers
This job is done with the wheels off, for example during a seasonal tire swap. This guide covers the Model 3 with standard brakes (not Performance): the front calipers stay on the steering knuckle and the pads are removed by driving out the pins, while the rear calipers come off the bracket. If your car has Performance brakes, the calipers are removed completely along with the rotors, and the bolt torque is different. The brake fluid is not drained and the hoses are not disconnected.
Key figures
- Rear caliper bolt torque26 N·m (19 lb-ft), using a torque wrench in step 20; if the bolt heads are deformed, replace the bolts
- Performance caliper bolt torque83 N·m (61 lb-ft) rear, 94 N·m (69 lb-ft) front, only for Performance brake versions where the calipers are removed completely (see Warning)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the caliper, pads, bracket, disc and hub are
Tap to enlarge
- 1Caliper: a cast clamp fitted over the disc edge. At the front the pads come out by knocking out the pins and the caliper stays; at the rear it is removed from the bracket by two bolts (26 Nm).
- 2Pads: sit on both sides of the disc inside the caliper. Clean their edges and lubricate only the metal edges. Do not mix up inner and outer.
- 3Bracket with two bolts: holds the caliper. At the rear remove these two bolts and tighten them to 26 Nm on assembly. Do not twist or stretch the hose.
- 4Brake disc: inspect it and wipe it with cleaner. Keep grease off the disc.
- 5Hub with studs and a center nut: a landmark where the wheel mounts.
Parts
8| № | Part |
|---|---|
| 01 | Brake cleanerFind on Amazon → |
| 02 | Brake caliper guide lubricantFind on Amazon → |
| 03 | Silaramic grease for metal pad edgesFind on Amazon → |
| 04 | Front caliper retaining pinsreplace only if worn or damagedFind on Amazon → |
| 05 | Front caliper anti-rattle springsreplace only if worn or damagedFind on Amazon → |
| 06 | Rear bracket abutment clipsreplace only if worn or damagedFind on Amazon → |
| 07 | Rear caliper boltsif the heads are deformedFind on Amazon → |
| 08 | Brake padsonly if wornFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
12- Jack or lift Amazon →
- jack stands Amazon →
- torque wrench Amazon →
- sockets and Torx wrench (external E18 for the rear caliper bolts) Amazon →
- pin punch and hammer Amazon →
- caliper spreader (or C-clamp for retracting the pistons) Amazon →
- S-hook for hanging the caliper Amazon →
- nylon and steel brushes Amazon →
- brake caliper file (brake file) Amazon →
- pad puller Amazon →
- respirator Amazon →
- lint-free rags Amazon →
Step by step
26 steps · 4 stagesStage 1 of 4 Preparation 5 steps
- Put on a respirator and gloves: brake dust is harmful. Do not blow the dust off with compressed air. Use only brake cleaner and a brush.
- Open the hood and remove the rear underhood apron to reach the brake fluid reservoir.
- Place an absorbent cloth under the brake fluid reservoir, wipe the reservoir around the cap, and remove the cap: the fluid level will rise when you retract the pistons.
- Enable Tow Mode: screen, car icon, Service, Towing. Turn on the electronic parking brake service mode (EPB Service Mode), otherwise the rear pistons will not retract.
- Raise the car on a lift or with a jack at the factory lift points, set it on jack stands, and remove all four wheels (lug nut torque for installation is per the manufacturer's specification).
Stage 2 of 4 Front calipers 9 steps
- Turn the steering wheel fully to one side so you can reach the left caliper.
- Use a pin punch to drive out the retaining pins and remove the anti-rattle spring from the front left caliper.
- Use a spreader to push the pistons back into the caliper. Watch the fluid level in the reservoir.
- Remove the pads. If they are stuck, use a pad puller. If there is heavy corrosion, tap the pins with a hammer and punch. Do not mix up the inner and outer pads: lay them out separately.
- Using a brush and brake cleaner, clean the abutment flats, the piston faces, the inside surfaces of the caliper, the pins, the springs, and the pad edges. Remove corrosion in escalating steps: nylon brush, then steel brush, then file. With the file, use only single forward strokes, 3-4 firm passes, and do not remove metal or coating.
- Apply a thin layer of caliper lubricant to the caliper abutment flats and to the pad edges that rest on them. Do not apply lubricant to the pad backing plates, the friction material, the rotor, or rubber parts (especially the piston boots). Immediately wipe off any excess with brake cleaner and a clean rag.
- Install the pads in their original positions (inner and outer not swapped), then install the spring and the pins with the punch.
- Rotate the rotor 180 degrees and wipe off any lubricant and dirt with brake cleaner. Repeat.
- Turn the steering wheel the other way and repeat steps 7-13 on the front right caliper.
Stage 3 of 4 Rear calipers 7 steps
- Set the wheels centered (straight ahead). Remove the 2 bolts of the rear left caliper (socket/wrench sized to the bolt), lift the caliper off the bracket, and hang it on an S-hook. Do not twist or stretch the hose.
- Remove the pads from the bracket, keeping them separate.
- Retract the rear piston with the caliper spreader.
- Using a brush and brake cleaner, clean the bracket's abutment clips, the piston face, and the inside surfaces of the caliper. Inspect the clips: replace them if they are corroded or damaged.
- Inspect and clean the rotor. Clean the pads and apply a thin layer of Silaramic grease to the metal edges of the pads. Do not apply it to the friction material or the backing plate.
- Install the pads in the bracket, fit the caliper, and tighten the 2 bolts to 26 N·m (19 lb-ft). If the bolt heads are deformed, replace the bolts.
- Repeat steps 15-20 on the rear right caliper.
Stage 4 of 4 Finishing and checking 5 steps
- Install the wheels (lug nut torque per the manufacturer's specification) and lower the car.
- On the touchscreen, press and hold Park to turn off EPB service mode, then exit Service Mode.
- Press the brake pedal several times until it feels firm.
- Check the brake fluid level and top up to the mark if needed. Close the reservoir cap, remove the cloth, and install the underhood apron.
- Take a test drive at low speed: check pedal travel and make sure there is no squealing or pulsation. In regions where roads are salted in winter, rinse the suspension components near the wheels with clean water after the job.
Common mistakes and warnings
- Brakes are a safety system
- If you lack experience, have the work done at a repair shop
- Do not let lubricant get on the rotors or the friction material of the pads: it sharply reduces braking performance
- Do not swap the pads between positions, and do not twist the caliper hoses
- Model 3 vehicles with Performance brakes are serviced differently (calipers and rotors are removed; caliper bolt torque is 83 N·m (61 lb-ft) at the rear and 94 N·m (69 lb-ft) at the front)
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Test drives
Tesla Model 3 Review
Electric cars from the American company Tesla are gaining popularity around the world and sell by the thousands. Not…
Read →
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →