← Model 3

Tesla Model 3 (2021): Brake Fluid Check and Replacement

Brake fluid absorbs moisture, which lowers its boiling point and increases the risk of corrosion in the hydraulic system. For the Model 3, the manufacturer calls for periodic checks of the fluid condition (guideline: every 2 years) and replacement based on the test result. This guide covers a full fluid replacement through the bleeder screws on the calipers. The car is electric, but this job does not involve the high-voltage system.

DifficultyMedium Time1.5-2 hours Steps27

Part

№PartAlternatives
01 DOT 3 or DOT 4 glycol-based brake fluidabout 1 L (1.1 qt), in a sealed containerFind on Amazon → AlternativesATECastrolMotul

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

9

Step by step

27 steps · 4 stages
Stage 1 of 4 Inspection and preparation 8 steps
  1. Park the car on a level surface, set the parking brake, and power the car off. Open the front trunk (frunk).
  2. Remove the trim panels covering the brake fluid reservoir (the removal order depends on the trim and model configuration; release the clips with a flat plastic pry tool). The reservoir is at the rear of the frunk, next to the bulkhead.
  3. Inspect the fluid: the level should be between the MIN and MAX marks. Dark, cloudy fluid or sediment means it is time to replace it.
  4. Test the fluid with a tester, either boiling point or moisture content. Guideline: if moisture is above roughly 3% or the boiling point is noticeably below the norm for the fluid type, the fluid needs to be replaced. A moisture test will show the fluid's condition even on a new car with little wear.
  5. If the test shows the fluid is in good condition, the check is complete: put the panels back. If the fluid is worn out, proceed to replacement.
  6. Prepare new fluid from a sealed container. Do not use a container that has been open for a long time: it has already absorbed moisture.
  7. Use a syringe or extractor bulb to remove the old fluid from the reservoir down to a level just above the MIN mark. Do not let the reservoir run completely empty, or air will enter the system. Wipe the reservoir walls with a clean, lint-free cloth.
  8. Top up with new fluid to the MAX mark. Wash any fluid that gets on the paint off immediately with water: it damages the clear coat.
Stage 2 of 4 Raising the car 4 steps
  1. Loosen the 21 mm lug nuts while the wheels are still on the ground.
  2. On the touchscreen, enable Jack Mode (in the service settings) so the system does not react to changes in body position.
  3. Raise the car only at the designated lift points under the rocker panels, using the dedicated rubber pads. Set the body on jack stands. Never work under a car supported only by a jack.
  4. Remove all four wheels to access the bleeder screws on the calipers.
Stage 3 of 4 Fluid replacement 7 steps
  1. Bleeding order: start with the wheel farthest from the reservoir and finish with the closest one. Verify the exact sequence in the manufacturer's service information.
  2. Remove the dust cap from the caliper bleeder screw, fit a clear hose onto the screw, and place the other end in a container holding a small amount of fresh fluid (the hose must stay submerged so air is not drawn back in).
  3. Power the car on (the Model 3 brake pedal is electronic and does not provide the needed effort without power). Have your assistant press the brake pedal gently several times, then hold it down.
  4. Loosen the bleeder screw 1/4-1/2 turn, let the fluid flow out, then close the screw before your assistant releases the pedal. Repeat until clean, fresh fluid with no air bubbles comes out of the hose.
  5. After every 2-3 cycles, check the reservoir and top up with fresh fluid to MAX. The level must not drop below MIN.
  6. Tighten the bleeder screw to the manufacturer's torque specification (guideline for a bleeder screw: 8-12 N·m (6-9 lb-ft); do not overtighten, the threads in the caliper are fine). Wipe the screw and fit the cap.
  7. Repeat steps 14-18 on the remaining wheels in the chosen order.
Stage 4 of 4 Reassembly and check 8 steps
  1. Install the wheels, tighten the lug nuts by hand, and lower the car to the ground.
  2. Tighten the lug nuts in a crisscross pattern with a torque wrench. Per Tesla's specification for the Model 3, the guideline is 125-135 N·m (92-100 lb-ft). Re-check the torque after 50-100 km (30-60 miles) of driving.
  3. Turn off Jack Mode on the screen.
  4. Check the reservoir level, top up to MAX, and close the cap. Reinstall the frunk trim panels.
  5. With the power on, press the brake pedal 10-15 times: the pedal should feel firm, with no sinking or sponginess. A soft pedal means air in the system, so repeat the bleeding.
  6. Inspect the bleeder screws, wheels, and brake hoses for leaks.
  7. Take a test drive at low speed in a safe area and test the brakes several times. Only then head out on the road.
  8. Take the used fluid to a recycling facility. Do not pour it down a drain or onto the ground.

Common mistakes and warnings

  • The brake system is critical for safety
  • If you have no experience bleeding brakes, it is better to leave this job to a repair shop
  • A soft pedal, a loss of fluid in the reservoir, or leaks after replacement mean the car must not be driven
  • If the reservoir ran empty during the work and air entered the system, and normal bleeding does not help, a service procedure with Tesla diagnostic equipment may be required to remove air from the ABS unit and the electric brake booster
  • Brake fluid is toxic and damages paint
  • Do not touch or disconnect the high-voltage orange cables: they are not needed for this job
  • The torque values in the text are approximate, so verify the exact values against the manufacturer's service information
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →