Autopapyrus · Lada Granta 1.6 8v 11186 (2015)
https://autopapyrus.com/catalog/lada/granta/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/lada/granta/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada Granta 1.6 8v 11186 (2015): Engine Oil and Oil Filter Change
Change the oil and filter on the 11186 engine every 15,000 km (the first change on a new or rebuilt engine is at 2,500-3,500 km). The lubrication system capacity is about 3.5 L (3.7 qt). Do the job with the engine warm, working from underneath the vehicle.
Key figures
- Drain plug tightening torqueset it on a torque wrench in step 9; tighter and you will strip the threads in the oil pan35-45 N·m (26-33 lb-ft)
- Engine oil capacityfirst pour in 3 L (3.2 qt) (step 15), then add the rest by the dipstick (step 19)about 3.5 L (3.7 qt)
- Drain plug wrench sizea socket or wrench works (step 6)17 mm
- Filter tighteningby hand only (step 14)another 3/4 turn after the seal touches
- Change intervalfirst change on a new engine or after an engine rebuild at 2,500-3,500 km15,000 km
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the oil filter is and what is next to it
Tap to enlarge
- 1Oil filter: a grey can with a ribbed side, pressed against the block next to the bracket. Unscrew counter-clockwise, with a filter wrench if needed.
- 2Crankshaft sensor connector: the black plug at the end of the corrugated harness next to the filter. Unplug it if needed to avoid damage.
- 3Rusty bracket with bolts above the filter: a landmark for finding the filter.
- 4Curved exhaust pipe above the filter: it is hot, work carefully.
- 5Stud and nut holding the pipe: a landmark above the filter.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Engine oil, synthetic or semi-synthetic, API SL/SM or SN, ACEA A3/B3 or A3/B4about 3.5 L (3.7 qt)Find on Amazon → | |
| 02 | Spin-on oil filter for VAZ 8-valve enginesFind on Amazon → | AlternativesMannBoschFiltron |
| 03 | Drain plug gasket (washer)if neededFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7Step by step
20 steps · 4 stagesStage 1 of 4 Preparation 4 steps
- Warm the engine up to operating temperature so the oil is thin and drains completely. Park the car on a level inspection pit or ramps, set the parking brake, and shut off the engine.
- Get ready a drain pan of 4 L (4.2 qt) or larger, rags, the new filter and the oil. The oil is hot, so wear gloves.
- If the car has an engine skid plate (undertray) that covers the drain hole or the filter, remove it.
- Unscrew the oil filler cap so the oil drains faster.
Stage 2 of 4 Draining the oil 5 steps
- Wipe the dirt off the oil pan around the drain plug with a rag.
- Loosen the drain plug with a 17 mm wrench or socket, then position the pan under the hole.
- Unscrew the plug by hand, holding onto it so it doesn't fall into the drained oil, and let the oil drain for at least 10 minutes.
- Wipe the plug and its seat, and inspect the threads and the seal; replace the gasket if it is damaged.
- Install the plug and tighten it to 35-45 N·m (26-33 lb-ft). Wipe any spilled oil off the pan.
Stage 3 of 4 Replacing the filter 5 steps
- Move the pan under the oil filter. To avoid damaging it, disconnect the wiring connector from the crankshaft position sensor located nearby if necessary.
- Unscrew the old filter counterclockwise; if it won't budge, use a filter wrench. More oil will still drain out of the filter.
- Wipe the mounting surface on the cylinder block with a rag and make sure the old rubber gasket hasn't stuck to the block.
- Pour a little fresh oil into the new filter (about halfway) and lubricate its rubber sealing ring with oil.
- Screw the filter on by hand until the ring touches the block, then tighten it about another 3/4 turn, by hand only, without tools. Reinstall the skid plate if you removed it, and reconnect the sensor connector.
Stage 4 of 4 Refilling and checking 6 steps
- Insert the funnel into the filler neck and pour in about 3 L (3.2 qt) of oil.
- Put the filler cap on and run the engine for 1-2 minutes. The low oil pressure warning light should go out.
- Check the drain plug and the filter for leaks. If either leaks, tighten it slightly.
- Shut off the engine, wait a few minutes for the oil to drain back into the pan, and check the level with the dipstick on level ground.
- Top up the oil to a level between the MIN and MAX marks, closer to MAX but not above it (excess oil can get into the combustion chambers and damage the catalytic converter).
- Take the used oil and old filter to a recycling collection point. Write down the mileage of the change.
Common mistakes and warnings
- The oil and engine parts are hot, so there is a risk of burns
- Do not overtighten the drain plug: the threads in the aluminum oil pan strip easily
- Tighten the filter by hand only
- After a couple of days, check the oil level and make sure there are no leaks