https://autopapyrus.com/catalog/lada/niva-travel/guides/headliner-removal-and-installation/
Lada Niva Travel (Gen 1): Headliner Removal and Installation
The exact headliner fastening layout of the Niva Travel is not documented in open service materials, so below is the general procedure for this type of headliner. Check the details against the manufacturer's service manual. The headliner is held in place by clips and screws, and its edges are tucked around the perimeter under the door opening weatherstrips and the pillar trims. Because of its size, it is easiest to remove the headliner through the rear door or the cargo opening by tilting it. Remove it without sharp bends: the headliner cracks and creases easily.
Diagram: where the headliner is attached and what to remove first
- 1Interior dome light: pry off the diffuser or housing with a plastic trim tool, disconnect the connector and set the lamp aside.
- 2Sun visors with holders: remove the mounting screws with a Phillips screwdriver and disconnect the mirror light connector if present.
- 3Overhead grab handles (several, left and right): fold back the screw caps and remove the screws.
- 4Door opening seals: black rubber along the headliner edge. Pull it out 15-20 cm at the edge of the headliner; no need to remove it entirely.
- 5Pillar trims: pry from edge to edge with a trim tool, releasing the clips one by one. Remove screws first if present. Be extra careful with side airbags.
- 6Rear-view mirror: disconnect it if it is mounted on the headliner or on the windshield next to the trim.
- 7Headliner: release the clips around the edge starting from the rear, hold it by hand, lower it and take it out through the rear door opening, tilting slightly.
Parts
2| № | Part |
|---|---|
| 01 | Headliner clips and push pins (set)some break during removalFind on Amazon → |
| 02 | Headliner, completeif the old one is deformed or tornFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
12 steps- Park the vehicle on a level surface and disconnect the negative battery terminal. This is mandatory if the headliner has a dome light, wiring or airbags (on trims with side airbags, do not pull or force the headliner near the pillars).
- Remove the dome light: pry off the lens or housing with a plastic trim tool, disconnect the connector and set the light aside.
- Remove the sun visors and their holders: remove the mounting screws with a Phillips screwdriver and disconnect the vanity mirror light connector, if equipped. Remove the overhead grab handles: pry back the screw covers and remove the screws.
- Pull back the door opening weatherstrips (front doors, rear doors and the rear door/tailgate) along the headliner edge. You can simply pull the rubber out 15-20 cm (6-8 in) near the headliner edge; there is no need to remove it completely.
- Remove the front, center and rear pillar trims: pry with a trim tool from edge to edge, popping the clips out one at a time so you don't break the plastic. If the trims are held with screws, remove them first. The front pillar trims are trickier: on vehicles with side airbags, be especially careful.
- Remove the interior rearview mirror if it is mounted on the headliner or on the windshield next to the headliner. Remove the plugs and fasteners around the roof rails if they pass through the headliner.
- Inspect the perimeter of the headliner: find any remaining screws, push pins and clips. If the headliner won't come free, there is a fastener you haven't spotted.
- Release the headliner from the clips: carefully pop it loose around the perimeter, starting at the rear edge, then moving to the sides and the front edge. Support the headliner with your hand so it doesn't fall.
- Lower the headliner and carefully guide it out through the rear door opening or the cargo area, tilting it slightly. Do not bend it sharply, to avoid leaving creases. Lay it on a clean, flat surface, face up.
- Before installation, inspect the body under the headliner: wiring, sound insulation, clip mounting points. Replace any broken clips and route the wiring so it won't be pinched.
- Installation is the reverse of removal: bring the headliner into the cabin, align the cutouts for the dome light and handles with the holes, press the clips in around the perimeter with light palm pressure, then reinstall the door opening weatherstrips, pillar trims, visors, handles and dome light. Tighten the mounting screws by hand with moderate force, without a torque wrench: plastic doesn't tolerate overtightening, and the service manual doesn't specify a significant torque for these screws.
- Reconnect the negative battery terminal, check the operation of the dome light and mirror lights, close and open all the doors, and make sure the headliner doesn't interfere with the door openings and the weatherstrips are seated properly.
Common mistakes and warnings
- If the vehicle is equipped with side airbags (curtain airbags), do not disassemble the pillars or disconnect the airbag connectors without experience: careless work can deploy the system or damage it
- If in doubt, leave the job to a repair shop
- Do not use excessive force: the headliner breaks easily, and a worn or crushed part cannot be restored