Autopapyrus · MG HS 1.5 turbo 15E4E (2026)
https://autopapyrus.com/catalog/mg/hs/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/mg/hs/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
MG HS 1.5 turbo 15E4E (2026): Engine Oil and Oil Filter Change
The oil in the 1.5-liter turbo engine of the MG HS is changed together with the filter about every 10,000-15,000 km or once a year, and more often under severe use. The fill capacity with the filter is about 4 L (4.2 qt). Owners also report 4.5-5 L (4.8-5.3 qt) in discussions, so add oil in stages and go by the dipstick. Do the job with the engine warm, but not hot.
Key figures
- Oil capacity with filterabout 4 L (4.2 qt). This is what is usually added at a change, but add oil in stages and check the dipstick (steps 17-18)
- Reference oil viscosity0W-20 with ACEA C5 approval. Check your owner's manual before buying oil
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Turbo engine oil, ACEA C5/C2about 4-4.5 L (4.2-4.8 qt)Find on Amazon → | |
| 02 | Oil filter for 1.5T engine (15E4E)cartridge element with sealing ring, or spin-onFind on Amazon → | AlternativesMannBoschFiltron |
| 03 | Drain plug washernewFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online).
See manuals →
Step by step
24 steps · 5 stagesStage 1 of 5 Preparation 5 steps
- Warm up the engine for 3-5 minutes until it is warm so the oil flows easily. Do not let it get hot, to avoid burns.
- Park the car on level ground and set the parking brake. If you lift the car, support it on jack stands or a lift, not on a jack alone.
- Shut off the engine and wait 5-10 minutes so the oil drains down into the oil pan.
- Open the hood, unscrew the oil filler cap and pull out the dipstick. This speeds up draining.
- Lay out rags and get the drain pan ready.
Stage 2 of 5 Draining the old oil 5 steps
- Remove the engine undershield if fitted. It is usually held by bolts or screws, so note where each one goes.
- Locate the drain plug at the bottom of the oil pan and place the pan under it.
- Loosen the plug with a socket, then unscrew it by hand. Hold it in place and pull it away quickly at the end so you don't get oil on yourself.
- Let the oil drain for 10-15 minutes until it only drips occasionally.
- Wipe the plug threads and the seating surface, and replace the sealing washer with a new one.
Stage 3 of 5 Replacing the filter 4 steps
- Locate the oil filter on the engine block and place the pan or rags under it: residual oil will run out of the housing.
- If the filter is the cartridge type in a plastic housing, unscrew the housing cover with a socket, remove the old element, and take the old sealing rings off the cover. If the filter is spin-on, remove it with a filter wrench or by hand with a glove.
- Lubricate the sealing ring of the new filter or cover with fresh oil. Make sure the old ring is not left stuck on the mounting surface.
- Install the new filter or element. Tighten a spin-on filter by hand, about 3/4 turn after the gasket touches, without a wrench. Tighten the housing cover with a torque wrench. The cover torque is approximately 20-25 N·m (15-18 lb-ft); check the exact value against the manufacturer's specifications.
Stage 4 of 5 Refilling 5 steps
- Install the drain plug with the new washer. The tightening torque is approximately 25-35 N·m (18-26 lb-ft); check the exact value against the manufacturer's specifications. Do not overtighten: threads in an aluminum oil pan strip easily.
- Reinstall the engine undershield if you removed it.
- Using a funnel, pour about 3.5 L (3.7 qt) of oil into the filler neck, wait a minute, and check the level with the dipstick.
- Add oil in small amounts up to the upper dipstick mark (about 4 L (4.2 qt) with the filter; the actual amount may differ slightly). Do not fill above the upper mark: overfilling causes the oil to foam and the engine to smoke.
- Close the filler neck with the cap and insert the dipstick.
Stage 5 of 5 Checking 5 steps
- Start the engine and run it for 1-2 minutes. The oil pressure light should go out a few seconds after startup.
- Inspect the plug and the filter for leaks.
- Shut off the engine, wait 5-10 minutes, and check the level on the dipstick again. Top up to the upper mark if needed, but not above it.
- Reset the maintenance interval indicator through the instrument cluster menu or following the instructions in the owner's manual.
- Take the used oil to a collection point. Do not pour it on the ground or down a drain.
Common mistakes and warnings
- The oil and the exhaust system are hot, so wear gloves
- Do not let the oil level go above the upper or below the lower dipstick mark: either one damages a turbo engine
- Use only oil that meets the specification given in your vehicle's owner's manual
- A jack is not a substitute for jack stands: do not get under a raised car without secure support