Autopapyrus · Nissan Murano 3.5 V6 VQ35DE (2005)
https://autopapyrus.com/catalog/nissan/murano/guides/drive-belt-serpentine-belt-replacement/
https://autopapyrus.com/catalog/nissan/murano/guides/drive-belt-serpentine-belt-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Nissan Murano 3.5 V6 VQ35DE (2005): Drive Belt Replacement (Alternator Belt)
The Murano Z50 with the VQ35DE has two belts. One drives the alternator and A/C compressor, and the other drives the power steering pump. The alternator belt sits closer to the engine, so you must first loosen and remove the power steering pump belt to get to it. Tension is set with the idler pulley adjusting bolt, not an automatic tensioner.
Key figures
- Force for the deflection check98 N (about 10 kgf, or 22 lbf). Press with this force at the midpoint between the pulleys, then measure the belt deflection (step 16)
- When to check tensionengine cold or stopped for more than 30 minutes (step 16)
- Crankshaft revolutions before rechecking2 or more. After that, set the tension again (step 17)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
4| № | Part | Alternatives |
|---|---|---|
| 01 | Serpentine belt for alternator and A/C compressor, Nissan Murano Z50 (VQ35DE)Find on Amazon → | AlternativesGatesBandoContitech |
| 02 | Power steering pump beltoptionalFind on Amazon → | |
| 03 | Drive belt tensioner pulleyif noisy or looseFind on Amazon → | |
| 04 | Drive belt idler pulleyif noisy or looseFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more.
See manuals →
Step by step
22 steps · 4 stagesStage 1 of 4 Preparation 4 steps
- Let the engine cool down, set the parking brake and shut off the engine.
- Inspect the old belt for cracks, fraying, oil contamination and rib wear. A belt soaked in oil or coolant is a sign you need to find the leak.
- Take a photo of the belt routing on the pulleys. Note which belt runs on which pulley.
- Raise the front of the vehicle and set it on jack stands, or use a service pit. Remove the right (passenger-side) engine undercover and the right splash guard under the right wheel.
Stage 2 of 4 Belt removal 7 steps
- Locate the idler pulley with the adjusting bolt and lock nut. The bolt is coated with grease. Do not let it get on the belt.
- Loosen the mounting and back out the adjusting bolt until the belt is completely slack. Start with the power steering pump belt, since it is the outer one.
- Remove the power steering pump belt from the pulleys.
- Release the tension on the alternator and compressor belt the same way.
- Remove the alternator and compressor belt from the pulleys.
- Check the pulleys and idlers: spin them by hand and check for noise, play and scoring in the grooves. Replace a worn idler.
- Wipe the pulley grooves clean of oil, dirt and coolant.
Stage 3 of 4 Installation and tensioning 7 steps
- Install the new belts in the reverse order of removal: the alternator and compressor belt first.
- Make sure all the belt ribs sit in the grooves of every pulley. Check that there is no oil or coolant on the belt or pulleys.
- Install the power steering pump belt.
- Set the tension with the adjusting bolt to the value in the service manual. Tighten the idler pulley lock nut finger-tight so you can measure the tension without play.
- Deflection check: with the engine cold (or stopped for more than 30 minutes), apply 98 N (about 10 kgf, or 22 lbf) at the midpoint between the pulleys. The allowable deflection is given in the manufacturer's service manual table.
- Turn the crankshaft two or more full revolutions, then check again and readjust if needed so the tension is even between the pulleys.
- Tighten the lock nut and the adjusting bolts to the torque specified by the manufacturer. As a rough guide, bolts like these take 20-50 N·m (15-37 lb-ft). Check the exact value in the service manual.
Stage 4 of 4 Finishing up and checking 4 steps
- Reinstall the undercover and the wheel, then lower the vehicle.
- Start the engine and check how the belts run: no squealing, wobble or belt walking to one side.
- Turn on the A/C, turn the steering wheel to full lock in both directions and make sure there is no squealing.
- Check the tension again after 100-200 km (60-120 miles), because a new belt stretches.
Common mistakes and warnings
- Keep your hands and tools away from the rotating pulleys when starting the engine
- Do not use belts that have cracks or oil stains
- An overtightened belt ruins the alternator and power steering pump bearings, while a loose belt squeals and slips
- If the belt "walks" to one side or makes noise after replacement, check the pulley alignment and the condition of the idlers
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Nissan
Over the course of 80 years, this Japanese automaker has come a long way and risen to become a leader of the global…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →