← Duster

Renault Duster 2.0 F4R (2018): Center Muffler (Resonator) Replacement

The Duster exhaust system consists of a flex pipe (expansion joint), a catalytic converter, a center muffler (resonator) and a rear (main) muffler. The pipe from the manifold flange is a single piece, so the center muffler is cut out of the pipe and the new one is connected to the old pipe with special clamps. The work is done under the vehicle, without removing the engine.

DifficultyMedium Time1.5-3 hours Steps14

Key figures

  • Distance between the cut marks on the pipe
    about 80 mm. Cut midway between the marks (steps 3 and 7)
  • Single-bolt repair coupling torque
    25 N·m (18 lb-ft). Use a torque wrench in step 12; do not overtighten, or the pipe will deform
  • Two-bolt repair coupling torque
    18 N·m (13 lb-ft). Same as above, step 12

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where to cut the exhaust pipe and what to remove when replacing the middle muffler

View of the exhaust from below, lying under the carCar underbodyflex jointabout 80 mmabout 80 mmclamps must not touch the shield1223456Catalytic converter: do not cutCut near converterCut near rear mufflerMiddle mufflerRubber mount on bracketRear mufflerHeat shieldTap to enlarge
  1. 1Catalytic converter: the ceramic inside is fragile, do not cut or hit it. Cut only the pipe after it.
  2. 2Cut places: there are two, one on each side of the middle muffler. The pipe has two marks about 80 mm apart, cut midway between them (marker first, then hacksaw or pipe cutter).
  3. 3Middle muffler (resonator): it is cut out of the pipe and lowered down, the new one is joined to the pipes with clamps. Fit new clamps on both joints.
  4. 4Rubber mount on the pipe bracket: wet it with soapy water and pry with a screwdriver from both sides, or cut it with a knife if replacing it. The bracket is pulled out of it when removing the resonator.
  5. 5Rear muffler: hold it so the system does not sag after the cut.
  6. 6Heat shield: turn the clamps so their bolts do not touch it, and keep the pipe and mufflers off the underbody.

Parts

3
№Part
01 Center muffler (resonator), Duster 2.0 F4R exhaustFind on Amazon →
02 Exhaust pipe clampsone per joint, usually 2 pcsFind on Amazon →
03 Rubber exhaust hangersif wornFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Step by step

14 steps
  1. Let the exhaust system cool down completely. Put the vehicle over a pit or on ramps. If you raise it with a lift or a jack, always use jack stands. Never work under a vehicle supported only by a jack.
  2. Treat the threads and pipe joints with penetrating oil and wait a few minutes.
  3. Inspect the center muffler: find its joints with the catalytic converter and with the rear muffler, as well as the rubber hanger on the bracket of its pipe. The pipe usually has two cut-zone marks about 80 mm apart; make the cut midway between them.
  4. If oxygen sensors or wiring near the cut zone are in the way, carefully move the wiring aside. Do not unscrew the sensors unless necessary.
  5. Remove the rubber hanger of the center muffler from the brackets: wet the gap with soapy water and pry it off with a screwdriver from both sides. If you are replacing the hanger anyway, you can cut it off with a knife.
  6. Support the rear muffler (if necessary, remove its rubber hangers from the brackets after wetting them with soapy water) so the system does not sag on the remaining mounts after the cut.
  7. Mark the cut line with a marker midway between the marks, on the pipe at the catalytic converter and on the pipe leading to the rear muffler. Cut both pipes with a hacksaw or pipe cutter, taking care not to damage neighboring pipes, heat shields and wiring. Remove burrs with a file.
  8. Lower the center muffler out, pulling its bracket out of the rubber hanger.
  9. Test-fit the new resonator: its inlet and outlet pipes must slide onto the remaining pipes all the way, without pressing against the underbody. Clean rust and scale from the ends of the old pipes.
  10. Slide the clamps on and insert the pipes into the resonator's inlet and outlet all the way, and insert the resonator bracket into the rubber hanger (wet the hangers with soapy water beforehand and clean the body brackets). Do not fully tighten the clamps until you have set the position.
  11. Align the system: the resonator and rear muffler must not touch the underbody, rocker panels, rear axle or each other, and the clearance to the body and shields must be even. Rotate the clamps so the bolts do not touch the heat shields.
  12. Tighten the clamps evenly. The torque depends on the clamp type (for repair couplings: single-bolt, 25 N·m (18 lb-ft); two-bolt, 18 N·m (13 lb-ft)); for branded exhaust clamps, follow the clamp manufacturer's specification. Do not overtighten, to avoid deforming the pipe.
  13. Start the engine and check the joints for exhaust leaks and hissing. If a single-bolt coupling hisses, apply exhaust system sealant to the joint. If that does not help, remove the clamp, check the pipe ends for burrs and deformation, and reinstall it.
  14. Make sure nothing touches or rattles against the body and that all heat shields are in place and secured. Take a test drive and make sure there are no knocking noises from under the vehicle.

Common mistakes and warnings

  • Do not cut or hit the catalytic converter: it contains brittle ceramic that breaks from impacts
  • Always use new clamps; never reuse old ones
  • Do not work on a hot exhaust system and do not get under a vehicle supported only by a jack
  • Wear safety glasses and gloves when using a hacksaw and working with rust
  • If you have no experience working under a vehicle or cannot lift it securely, leave the job to a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →