← Twingo Renault Twingo repair manuals →

Renault Twingo II 1.2 16V D4F 75 hp (2008): Engine Oil and Oil Filter Change

The oil on the 1.2 16V (D4F) is changed together with the oil filter. The engine's refill capacity is about 4 L (4.2 qt). The filter sits low, above the subframe, and access is tight, so you will need a filter wrench and a little patience. This guide covers the 1.2 16V gasoline engine. The 1.5 dCi diesel has a different oil capacity and filter location.

DifficultyEasy Time1-1.5 hours Steps21

Key figures

  • Oil capacity
    about 4 L (4.2 qt). This is how much to add when changing the oil together with the filter. Add it in portions and check against the dipstick (step 15)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: what you need for the oil change: filter, wrench and new washer

Filter, wrench and washer side by side1Oil filter2Rubber ring on the face3Square-drive wrench for the plug4Drain plug washerFilter lying on its side: the rubber ring runs along the edge of the faceTap to enlarge
  1. 1New spin-on oil filter. Pull the old one off with a filter wrench, screw the new one on by hand and tighten about 3/4 of a turn more.
  2. 2Rubber ring along the edge of the filter face. Smear it with a thin layer of oil with your finger, and make sure no old ring is left on the engine.
  3. 3Square-drive wrench (or socket): used to undo the drain plug in the oil pan.
  4. 4New sealing washer: a thin ring with a hole. Fit it on the cleaned drain plug.

Parts

3
№PartAlternatives
01 Spin-on oil filter for RenaultFind on Amazon → AlternativesMannBoschFiltron
02 Engine oil, Renault-approved for gasoline enginesabout 4 L (4.2 qt)Find on Amazon →
03 Drain plug sealing washernewFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 2 more. See manuals →

Step by step

21 steps · 5 stages
Stage 1 of 5 Preparation 3 steps
  1. Warm up the engine for 3-5 minutes so the oil thins out and drains better. The oil and parts will be hot, so wear gloves.
  2. Park the car on level ground. Lay plastic sheeting or cardboard under it. Raise the car onto ramps, or lift it with a jack and set it on two jack stands. Apply the parking brake. On ramps, also put the car in gear and place wheel chocks behind the rear wheels.
  3. Open the hood, remove the oil filler cap and pull out the dipstick. This lets the oil drain faster.
Stage 2 of 5 Draining the oil 3 steps
  1. Place the drain pan under the drain plug in the oil pan and slide it as close as possible so the oil does not splash.
  2. Unscrew the drain plug with the square-drive key or a socket. For the last turns, unscrew the plug by hand and quickly move it aside so you do not drop it into the pan.
  3. Let the oil drain for 10-15 minutes. While the oil drains, get the new filter and oil ready.
Stage 3 of 5 Replacing the filter 5 steps
  1. Move the pan, or a small container, under the oil filter. It sits above the subframe, and the leftover oil will run out of it.
  2. Use a cup or strap wrench to break the old filter loose. Then unscrew it fully by hand and lift it out straight up and down so you do not spill oil onto the subframe.
  3. Wipe the mounting surface on the engine with a clean rag. Make sure the old rubber gasket did not stay behind on the engine.
  4. Coat the rubber gasket of the new filter with a thin layer of fresh or drained oil (with your finger).
  5. Screw the new filter on by hand until the gasket touches the mounting surface, then tighten it about another 3/4 turn. Tighten the filter by hand only; do not use the wrench for tightening. If you have a torque wrench with a filter cup, the tightening guideline is about 15-20 N·m (11-15 lb-ft) (check the exact value against the manufacturer's specification).
Stage 4 of 5 Closing the drain and refilling 5 steps
  1. Clean the drain plug and the threads in the oil pan. Install a new sealing washer.
  2. Thread the plug in by hand, then tighten it with the torque wrench. The tightening guideline is 20-25 N·m (15-18 lb-ft) (check the exact value against the manufacturer's specification). Do not overtighten: the oil pan is thin and the threads strip easily.
  3. Remove the drain pan and tools, and inspect the area under the engine. Lower the car to level ground.
  4. Using the funnel, slowly pour in about 3.5 L (3.7 qt) of oil. Wait a minute and check the level with the dipstick. Add oil in small amounts up to the MAX mark. Do not overfill: excess oil foams and is forced out through the seals.
  5. Put the cap back on the oil filler and reinsert the dipstick.
Stage 5 of 5 Checking and resetting the service interval 5 steps
  1. Start the engine for 20-30 seconds. The oil pressure light should go out right away. If it does not, shut the engine off immediately and check the filter and the plug.
  2. Shut off the engine, wait 5 minutes and check the level with the dipstick again. Top up to MAX if needed.
  3. Inspect the filter and the plug: there should be no signs of oil leaking. Check again after the first drive.
  4. Reset the maintenance reminder on the instrument cluster. Turn the ignition on and briefly press the button on the right steering column stalk until the distance to the next service appears. Hold the button until the display starts to flash and shows the new interval, then it stops flashing. Turn the ignition off.
  5. Take the used oil and filter to a recycling collection point. The change interval is once a year or every 10,000-15,000 km (6,000-9,000 mi), and closer to the lower end with frequent short trips and city driving. Check the car's service book for the exact interval.

Common mistakes and warnings

  • Hot oil and the exhaust manifold can cause burns, so wear gloves
  • Do not work under a car supported only by a jack: use jack stands or ramps
  • Do not fill the oil above the MAX mark
Spotted a mistake? Tell us →

Our articles

More articles →