← Rexton SsangYong Rexton repair manuals →

SsangYong Rexton 2.2 Diesel D22DTR (2022): Engine Oil and Oil Filter Change

On the Rexton II (Y400) with the 2.2 diesel (listed in the catalog as D22MPI, and the engine is also known as D22DTR), the oil and filter are changed together. The fill capacity is about 6 L (6.3 qt). Change interval: 10,000 km or 6 months under severe conditions (city driving, heavy traffic, towing), or 15,000 km or 12 months under normal use. All you need is a level surface and a way to lift the vehicle.

DifficultyEasy Time40-60 minutes Steps13

Key figures

  • Engine oil capacitythe amount to buy and fill; start with 5.5 L (5.8 qt) and top up by the dipstick (step 10)
    about 6 L (6.3 qt)
  • Change intervalwhen to do the next change
    10,000 km or 6 months under severe conditions, 15,000 km or 12 months under normal conditions

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the oil drain plug and filter are and where to place the container

View from below, under the carPlace a containerunder the plugHoseSubframe1Oil filter2Drain plug3Oil pan4Front wheelTap to enlarge
  1. 1Oil filter: black ribbed cylinder on a flange beside the pan. Put a rag under it, remove it and replace it together with the oil.
  2. 2Drain plug at the bottom of the pan: place a container under it, unscrew it and drain all the oil. Refit with a new washer.
  3. 3Oil pan: the ribbed part under the engine. If a skid plate is fitted, remove it first.
  4. 4Front wheel: a landmark showing which side the pan is on.

Parts

4
№PartAlternatives
01 5W-30 engine oil, low-ash, ACEA C3 (for diesel with particulate filter)about 6 L (6.3 qt)Find on Amazon →
02 Oil filter for D22DTR 2.2 engineFind on Amazon → AlternativesMannBoschFiltron
03 Drain plug sealing washernewFind on Amazon →
04 Oil filter housing cap seal setfor a cartridge filter in a housingFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

13 steps
  1. Warm up the engine for 5-10 minutes so the oil thins out and drains completely. Shut off the engine and wait 5 minutes for the oil to drain into the oil pan.
  2. Park the vehicle on a level surface and set the parking brake. Raise the vehicle on a lift or place it on jack stands. Never rely on a jack alone.
  3. If there is an underbody skid plate beneath the engine, remove it. The fasteners vary, so go by what is installed.
  4. Place the drain pan under the drain plug in the oil pan. Loosen the plug, starting with light force, and drain the oil completely. This takes about 10-15 minutes.
  5. While the oil drains, locate the oil filter. Put a rag or pan under it. Remove it or unscrew the housing cap, depending on the design, and pull out the old filter element. With a cartridge design, replace the housing cap seals with new ones.
  6. Wipe the filter seating surface clean of dirt. Lightly coat the seal of the new filter with clean oil.
  7. Install the new filter or cartridge. Tighten a spin-on filter by hand, and tighten the housing cap with a torque wrench to the manufacturer's specified torque. Do not overtighten: plastic housings crack easily.
  8. Wipe the drain plug and its seat in the oil pan. Fit a new drain plug washer and thread in the plug. Tighten it with a torque wrench to the manufacturer's specified torque. For reference, on most similar diesels the plug is tightened in the range of about 25-40 N·m (18-30 lb-ft).
  9. Reinstall the skid plate if you removed it. Lower the vehicle onto level ground.
  10. Pour about 5.5 L (5.8 qt) of oil through the oil filler neck, wait a couple of minutes, and check the level with the dipstick. Top up to the MAX mark. Do not overfill: excess oil harms the engine and the particulate filter.
  11. Start the engine and let it run for 30-60 seconds. The oil pressure light should go out within a few seconds. Check the filter and drain plug for leaks.
  12. Shut off the engine, wait 5 minutes, and check the dipstick level again. Top up if needed.
  13. Reset the service interval indicator, if equipped. Take the used oil and filter to a recycling collection point.

Common mistakes and warnings

  • For a diesel with a particulate filter, use only low-ash oil with the correct approval, because regular oil clogs the particulate filter
  • Hot oil and engine parts can cause burns, so wear gloves
  • If you have no experience working under a raised vehicle, take it to a repair shop
  • Check the fill capacity, oil grade and torque specifications against the vehicle's owner's manual
Spotted a mistake? Tell us →