← Rexton SsangYong Rexton repair manuals →

SsangYong Rexton (1st generation): Rear Brake Pad Inspection and Replacement

The Rexton's rear brakes are discs, and the parking brake uses separate shoes inside a drum section of the rotor. Because of this, the caliper piston is pushed back in the usual way, without rotating it. Different versions come with different calipers and rotors, so always compare new parts with the old ones. New pads have a friction layer about 14-15 mm thick, and rear-axle rotors are typically 10 to 20 mm thick depending on the version.

DifficultyMedium Time1-1.5 hours for both sides Steps16

Key figures

  • Minimum thickness of the rear solid rotor (299 mm)measure with a caliper gauge in step 7; if thinner, replace the rotors as a pair
    8.5 mm
  • Minimum thickness of the rear ventilated rotor (307 mm)same, step 7
    18.4 mm
  • New rear pad thicknesscompare with the old pads in steps 4 and 11 to buy pads of the correct size
    about 14-15 mm

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

4
№PartGenuine part no.Alternatives
01 Rear disc brake pad set (with anti-squeal shims)per axleFind on Amazon → 4841308051 AlternativesBremboPagidTRW
4841308050
02 Rear brake rotorsif neededFind on Amazon → 4840105101
03 Caliper guide pinsFind on Amazon →
04 Caliper rebuild kitFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

9
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

16 steps
  1. Park the vehicle on level ground. Do not apply the parking brake. Instead, chock the front wheels and release the parking brake lever. Loosen the rear lug nuts while the wheels are still on the ground.
  2. Raise the rear axle with the jack, place jack stands under the body, and remove the wheels. Never work under a vehicle supported only by a jack.
  3. Inspect the caliper and hose for brake fluid leaks, cracks in the hose, or a misaligned piston dust boot. A leak means you should stop and replace the seals or the caliper.
  4. Check the pad thickness. If the friction layer is thinner than 3 mm, or wear is uneven (the inner pad is worn more than the outer), replace both pads on the axle. Always replace the pads on both sides as a set.
  5. Remove the two caliper guide bolts (hold the guide pins with a wrench), take off the caliper, and hang it from a wire or hook. The hose must not hang under load.
  6. Remove the old pads and anti-squeal shims, and note the position of the shims and spring clips.
  7. Inspect the rotor. Deep grooves, a lip at the edge, blue heat spots, or heavy corrosion mean the rotors should be replaced as a pair. The minimum thickness is 8.5 mm for the solid 299 mm rotor (version up to 02/2006, with ABS) and 18.4 mm for the ventilated 307 mm rotor. Measure with a caliper gauge in several places. The minimum thickness is also marked on the rotor itself.
  8. If you are replacing the rotor: remove the caliper bracket, then take the rotor off the hub (it sometimes seizes, so tap it carefully with a copper mallet). Clean the hub mounting surface, then install the new rotor after degreasing it to remove the protective coating.
  9. Clean the caliper bracket and the pad seats with a wire brush. Apply a thin layer of special grease to the guide pins, make sure the boots are intact, and check that the pins slide freely.
  10. Push the caliper piston back in with a C-clamp or a special tool (use an old pad against the piston to avoid damaging it). Watch the fluid level in the reservoir. It will rise, so do not add fluid, and draw off the excess with a syringe if necessary.
  11. Install the new pads with the anti-squeal shims. Apply a thin layer of brake grease to the back sides of the pads (do not grease the friction surface or the rotor).
  12. Install the caliper and tighten the guide bolts with a torque wrench. The torque is approximately 25-35 N·m (18-26 lb-ft) per the manufacturer's specification. Check the exact value against the specification.
  13. Install the wheels and tighten the lug nuts in a crisscross pattern. Lower the vehicle and tighten the lug nuts with a torque wrench to the manufacturer's specification for the Rexton wheels.
  14. Press the brake pedal several times until it feels firm so the pistons seat. Check the fluid level in the reservoir.
  15. Check the parking brake. It works with separate shoes inside the rotor, and after replacing rotors it sometimes needs adjustment. The lever should engage firmly within a few clicks.
  16. Bed in the new pads: drive 200-300 km without hard braking so they wear in against the rotor.

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience working on brake systems, have a repair shop do the job
  • Do not breathe brake dust, and do not use compressed air to clean it off
  • Use only brake cleaner
  • If the pedal sinks to the floor after the replacement, stop and inspect the system
  • The torque values for the caliper guide bolts and lug nuts in this guide are approximate
  • Check the exact values against the manufacturer's specification
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →