← Legacy Subaru Legacy repair manuals →

Subaru Legacy 2.0 EJ20G (1993): Engine Oil and Oil Filter Change

Lubrication system maintenance on the EJ20G comes down to changing the oil and filter, checking the level and inspecting for leaks. Oil works harder in a turbocharged engine, so it is best to keep the interval short. For engines in this family, the usual interval is about 7,500 miles (roughly 12,000 km) or 7.5 months. Under severe conditions (short trips, dust, cold, towing, rough roads), change it more often.

DifficultyEasy Time40-60 minutes Steps14

Key figures

  • Oil pan drain plug torqueset it on the torque wrench in step 5; do not exceed it, or you will strip the threads in the aluminum oil pan
    44 N·m (32 lb-ft)
  • Filter turn after the seal makes contacttighten by hand or with a filter wrench in step 9; overtightening causes leaks
    about 3/4 of a turn
  • Oil change intervalwhichever comes first; more often under severe conditions (see summary)
    7,500 miles (about 12,000 km) or 7.5 months

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the oil filter is and how to unscrew it

Seen from below, lying under the carEngine block, view from below and the sideExhaust pipe with a flangeTurn counterclockwiselooking at the end from below1Oil filter2Seat on the block3Exhaust pipe, hot4Oil pan, drain plugWhat the spot looks like without the filter2Wipe the surface around it5End face: turn this wayTap to enlarge
  1. 1Oil filter: a black can with a ribbed side, mounted on the side of the block. Place a rag and a pan, unscrew with a filter wrench counterclockwise as seen looking at the end from below.
  2. 2Seat on the block: the flat surface where the filter gasket sits. Wipe it and make sure the old rubber gasket did not stay stuck.
  3. 3Exhaust pipe with a flange and nuts below the filter. On a turbo engine it gets very hot: work only on a cooled exhaust.
  4. 4Oil pan and drain plug. After draining, tighten the plug to 44 Nm with a new washer, do not overtighten: the aluminum thread strips.
  5. 5End of the filter: the face you see from below. Unscrew counterclockwise; screw a new filter on by hand until the gasket touches, then about 3/4 of a turn more.

Parts

3
№PartAlternatives
01 Engine oil for turbocharged boxer engine (API SH/SJ or higher, Energy Conserving)Find on Amazon →
02 Oil filter for EJ20 engineFind on Amazon → AlternativesMannBoschPurflux
03 Drain plug sealing washernewFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 11 more. See manuals →

Step by step

14 steps
  1. Park the car on level ground and warm up the engine for a few minutes: warm oil drains more completely. Shut off the engine and wait 5 minutes so that combustion gases and vapor can clear. Pull out and wipe the dipstick so you can check the level against it later.
  2. Raise the car on a lift or set it on solid jack stands (not on a jack alone). If there is an underbody skid plate, remove it.
  3. Place the drain pan under the oil pan. Remove the oil filler cap on the valve cover: the oil will drain faster.
  4. Unscrew the oil pan drain plug and drain the oil completely. Wait until the stream stops. Be careful: the oil is hot.
  5. Wipe the plug and its seat, and replace the drain plug washer with a new one. Tighten the plug to 44 N·m (32 lb-ft). Do not overtighten: the oil pan is aluminum and the threads strip easily.
  6. Move the pan under the oil filter. Remove the filter with a filter wrench (on boxer engines it is mounted on the side of the block, and oil will run out of it, so keep a rag handy).
  7. Wipe the mounting surface on the housing. Make sure the old rubber gasket has not stayed stuck to the engine.
  8. Lubricate the rubber seal of the new filter with a thin layer of fresh oil. Pre-filling the filter with oil is not required, and with a side-mounted filter it is inconvenient anyway.
  9. Spin the filter on by hand until the seal touches the housing, then tighten about 3/4 of a turn more (per the manufacturer: about 3/4 of a turn after contact, no more). Do not overtighten with a wrench, or it will leak.
  10. Lower the car. Add oil through the filler neck in portions and check with the dipstick on level ground. As a guide, the capacity for this engine is about 4-5 L (4.2-5.3 qt) including the filter, but use the exact amount from the manufacturer's specification. Go by the dipstick, not the number: the level should be at the upper F mark.
  11. Close the filler cap and start the engine for 1-2 minutes. The oil pressure light should go out immediately. Inspect the drain plug and the filter for leaks.
  12. Shut off the engine, wait a few minutes and check the level on the dipstick again. Top up to the F mark if needed. Do not fill above F on a cold engine: warm oil expands, and if you check right after driving, the level may read between F and the notch.
  13. Take the used oil and filter to a collection point for disposal. Write down the mileage of the change.
  14. Check the oil level regularly (every 1-2 weeks and before a long trip): a small amount of oil consumption is normal for turbocharged boxer engines, but a sharp drop in level or blue smoke needs diagnosis. Mixing different oil brands when topping up is acceptable if the viscosity and class match.

Common mistakes and warnings

  • Work only on stable jack stands and with a cooled exhaust: on a turbo engine, the pipes and the turbocharger get very hot
  • If the oil pressure drops after the change or the light stays on with a warm engine, do not drive; check the level and the filter
  • Torque, capacity and viscosity are given as a guide based on the Subaru lineup; check the exact values for the EJ20G against the manufacturer's specification
Spotted a mistake? Tell us →