Autopapyrus · Toyota Mark II (X100, 2000)
https://autopapyrus.com/catalog/toyota/mark-ii/guides/fuel-filler-door-replacement/
https://autopapyrus.com/catalog/toyota/mark-ii/guides/fuel-filler-door-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Toyota Mark II (X100, 2000): Fuel Filler Door Replacement
On the Mark II (X100), the fuel filler door is attached to the rear right fender with a hinge held by two or three screws or bolts. The release is a cable running from a lever on the left side of the driver's seat. Most often, only the door itself needs replacing after an impact or when the hinge has corroded. This guide covers replacing the door. If the door won't open because of the cable, you'll also need steps 14-17.
Parts
4| № | Part |
|---|---|
| 01 | Fuel filler door with hinge and spring, body-color paintedFind on Amazon → |
| 02 | Fuel filler door release cableif the release is wornFind on Amazon → |
| 03 | Fuel door release lever by the driver's seatif the release is wornFind on Amazon → |
| 04 | Plastic clips for trunk trim and door sill trimspareFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Step by step
21 steps · 5 stagesStage 1 of 5 Preparation and diagnosis 4 steps
- Park the car on a level surface and turn off the engine. Find out what the problem is: the door is loose or bent (replace the door), or it won't open when you pull the lever (cable or latch).
- Pull the release lever by the driver's seat. If you hear the latch click but the door doesn't pop out, the spring or hinge is at fault. If the lever moves with no resistance, the cable is broken or has come off.
- If you plan to work on the cable, disconnect the negative battery terminal.
- Apply masking tape to the fender around the fuel door to avoid scratching the paint.
Stage 2 of 5 Removing the fuel door 4 steps
- Open the fuel door (if needed, open it by hand by prying the latch with a thin screwdriver through the tape). Remove the filler cap by turning it counterclockwise.
- Mark the position of the hinge on the body with tape or a marker so the new door goes on with the same gaps.
- Remove the hinge mounting screws or bolts while supporting the door with your hand.
- Remove the fuel door from the body. Inspect the mounting area: clean off dirt, and if there is rust, treat it with a rust converter and touch up the paint.
Stage 3 of 5 Installing the new fuel door 5 steps
- Transfer the spring, retainer and rubber stops to the new door if they are not included.
- Position the door at the marks and thread in the fasteners by hand.
- Close the door and check the gaps around the fender. They should be even, and the door should not stick out or sit recessed relative to the fender.
- If needed, loosen the fasteners, shift the door and tighten them for good. There is no strictly specified torque: tighten moderately, without stripping the threads in the thin body metal (for the exact value, follow the manufacturer's specification).
- Check that the lever opens the door and that the latch closes firmly.
Stage 4 of 5 Release cable (only if the door won't open) 4 steps
- Remove the plastic trim on the driver's door sill and the side trunk trim on the right and left, prying out the clips with a plastic trim tool.
- Pull back the weatherstrip and fold back the trim near the rear right fender, then find the end of the cable at the fuel door latch.
- Release the cable from the retaining clips along its path and detach it from the lever by the seat (the lever comes off by removing one or two plastic fasteners). Route the new cable with the same grommet, securing it with clips along the path of the old one.
- Reassemble the lever and check the cable travel before installing the trim.
Stage 5 of 5 Reassembly and check 4 steps
- Install the trunk trim and sill trim, replacing any broken clips.
- Reconnect the negative battery terminal.
- Open and close the fuel door with the lever several times and make sure it doesn't bind and latches securely.
- Install the filler cap and make sure it tightens until it clicks.
Common mistakes and warnings
- Work near the fuel filler neck away from open flames and don't smoke
- Keep gasoline off your skin
- Don't use much force on the hinge, because the fender is thin and bends easily
- Check the exact fastener torque values against the manufacturer's specification
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →