https://autopapyrus.com/catalog/toyota/prius/guides/engine-radiator-replacement/
Toyota Prius 1.8 Hybrid 2ZR-FXE (2016): Engine Radiator Replacement
The radiator on a 2016 Prius is installed together with the A/C condenser and the fan shroud. To remove it, you take out the air filter, the front bumper and several brackets. After replacement, you must refill the coolant and bleed the system in Maintenance mode. The job is labor-intensive, and you need to be careful around the A/C system and the inverter cooling circuit.
Key figures
- Coolant capacity of the engine system5.4 L (5.7 qt) (without the exhaust gas recirculation heat exchanger) or 6.0 L (6.3 qt) (with it): how much fluid to prepare and pour in at step 13
- Drain hose diameter9 mm inner diameter: fits on the radiator drain cock to drain the coolant into a container (step 4)
- Reservoir air bleed valve torque2.0 N·m (1.5 lb-ft): torque wrench with a 6 mm hex key, step 14; do not overtighten, it is plastic
- Fan motor screw torque3.9 N·m (2.9 lb-ft): only if you removed the motors from the shroud, step 11
- Fan nut torque6.3 N·m (4.6 lb-ft): do not mix up the left and right fans, step 11
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
2| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Toyota Prius XW50 engine radiator (2ZR-FXE, 1.8 Hybrid)Find on Amazon → | 16400-37310 | AlternativesDensoNissensKoyorad |
| 02 | Toyota Super Long Life Coolant (SLLC), ethylene glycol, free of silicates, amines, nitrites and borates, hybrid organic technologyFind on Amazon → |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
9- Socket set and ratchet Amazon →
- low-range torque wrench Amazon →
- 6 mm hex key Amazon →
- screwdriver Amazon →
- drain hose with 9 mm inner diameter Amazon →
- coolant catch container (at least 6 L (6.3 qt)) Amazon →
- plastic clip removal tools Amazon →
- gloves Amazon →
- scan tool or a way to enter Maintenance mode Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 5 more.
See manuals →
Step by step
17 steps- Let the engine and radiator cool down completely. Open the hood and make sure the vehicle is off (POWER button pressed, READY indicator off). Disconnect the negative terminal of the 12 V auxiliary battery in the trunk. Before doing so, wait for the period required by the service manual after power-off. After reconnecting the terminal, some systems will require initialization.
- Remove the plastic covers in the trunk that cover the battery terminal, and the covers in the engine compartment. Pull the decorative engine cover straight up, not forward, or it will break. Remove the radiator support trim panel (clips).
- Raise the vehicle. Remove the lower under-covers: the rear left engine under-cover and the No. 1 engine under-cover.
- Drain the coolant. Attach the 9 mm inner diameter hose to the radiator drain cock and put the other end in the container. Loosen the drain cock plug, then remove the reservoir cap so the fluid drains completely. Do not open the cap or the plug on a hot engine: hot fluid and pressurized steam cause severe burns. Take the drained coolant to a recycling facility. Tighten the drain cock plug by hand.
- Remove the air filter and intake duct, which block access: disconnect the mass air flow sensor connector, loosen the clamps, remove the cover and the air filter housing, and move the hoses and harness connectors off their brackets.
- Remove the complete front bumper, first disconnecting the connectors for the fog lights, sensors and washer, if equipped. This is a separate labor-intensive operation, so do it with a helper. Place the bumper on a soft surface.
- If the vehicle has an adaptive cruise control radar, disconnect its connector and remove the radar. Remove the horns (connectors and bolts) and any other brackets in the way. Note their positions. If necessary, remove the hood latch with its cable and the upper radiator support crossmember (bolts around the perimeter). Disconnect the latch cable carefully so you don't lose its adjustment later.
- Disconnect the upper and lower radiator hoses (No. 1 and No. 2). Mark their positions and the clamp orientation. Disconnect the hoses attached to the fan shroud and the cooling system bypass hoses. The inverter cooling circuit is separate: if its hoses are attached to the shroud or radiator, disconnect them carefully and place a container underneath. The inverter circuit will then need to be refilled and bled according to the service manual.
- Disconnect the fan motor connectors and the wiring harnesses on the shroud. Release the retainers (clips, hooks) and the bolts on the upper part of the shroud.
- Lift the radiator out together with the fan shroud, without putting force on the A/C condenser and lines. If the A/C system stays charged, do not disconnect its lines: move the condenser aside together with the lines, without kinking them. Remove the lower rubber radiator mounts.
- Transfer the lower rubber mounts to the new radiator. Remove the shroud fasteners from the old radiator and move the shroud with the fans to the new one. If you removed the fans from the motors, tighten the fan motor screws to 3.9 N·m (2.9 lb-ft) and the fan nuts to 6.3 N·m (4.6 lb-ft). Do not mix up or swap the left and right fans, or the parts will be damaged. Tighten the other radiator, shroud and bracket fasteners according to the manufacturer's specifications.
- Install the radiator in reverse order: first onto the lower mounts, then secure the upper part. Connect the fan connectors, hoses and bypass hoses, and secure them in the same places and with the clamps in their original positions. Install the bumper, radar, horns, hood latch (check its operation and adjustment), air filter and intake duct, covers and under-covers.
- Pour coolant into the reservoir to a level between the LOW and FULL lines. If the reservoir has an air bleed valve, first unscrew it with a 6 mm hex key. System capacity for the engine: 5.4 L (5.7 qt) for the version without the exhaust gas recirculation heat exchanger and 6.0 L (6.3 qt) for the version with it. Use only coolant; do not use plain water. The factory fill is Toyota SLLC.
- Squeeze the upper and lower radiator hoses by hand several times to push out air, and top up the fluid if the level drops. If you fitted a reservoir air bleed valve, tighten it to 2.0 N·m (1.5 lb-ft). Tighten the reservoir cap as tightly as possible.
- Enter Maintenance mode (inspection mode) according to the Toyota service manual so that the engine runs continuously. Before starting, turn off the A/C, set the heater temperature to maximum heat and the airflow to low speed. Warm the engine up until the thermostat opens (you can tell by the vibration of the upper hose in your hand). After the thermostat opens, let the coolant circulate for a few minutes and squeeze the hoses again to remove air. Do this while wearing gloves: the hoses are hot, and keep your hands away from the fans.
- Watch the reservoir level: it must not run empty. If the temperature gauge shows overheating, shut off the engine, let it cool and top up to FULL. After it cools, check that the level is between LOW and FULL. If it is below LOW, top up to FULL.
- Check the system for leaks (hoses, drain cock, radiator connections) and make sure the fans turn on. If the A/C circuit was opened, take the vehicle to a repair shop for vacuuming and refrigerant recharge. Close the under-covers and lower the vehicle. After a couple of drives, recheck the level on a cold engine.
Common mistakes and warnings
- This is a hard job: it involves removing the bumper and radar and working near the inverter circuit and the A/C system
- If you lack experience or the equipment to recharge the A/C, leave the job to a repair shop
- Do not cut open the orange high-voltage cables or disconnect their connectors; do all work with the vehicle off, and if high-voltage components must be touched, only a qualified specialist with certification and insulated gloves should do it
- Do not remove the reservoir cap on a hot engine
- The tightening torques for the radiator mounting, shroud and brackets given here are approximate; check the exact values in the manufacturer's service manual
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →