https://autopapyrus.com/catalog/toyota/prius/guides/thermostat-replacement-coolant-inlet-housing-with-thermostat/
Toyota Prius 1.8 Hybrid 2ZR-FXE (2016): Thermostat Replacement (Coolant Inlet Housing with Thermostat)
On this engine, the thermostat is built into a plastic coolant inlet housing mounted on the cylinder block under the air filter. It must be replaced as a complete assembly. To get access, you remove the left lower cover, drain the coolant, and take apart the air filter intake path together with the oil dipstick guide. The housing is held by 2 nuts and a bolt (type A) or by 3 bolts (type B), so check which one your car has.
Key figures
- Thermostat housing bolt and nut torque10 N·m (7 lb-ft). Use the torque wrench in step 10; the housing is plastic, so do not overtighten
- Oil dipstick guide bolt torque21 N·m (15 lb-ft). Step 12
- Thermostat opening temperature80-84 °C. For testing the old thermostat in water (step 8)
- Coolant capacity5.4 L (5.7 qt) without EHRS or 6.0 L (6.3 qt) with EHRS. How much to buy and fill in step 14
- Reservoir air bleed valve torque2 N·m (18 lb-in). Step 14, 6 mm hex key, tighten very lightly
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part |
|---|---|
| 01 | Thermostat with housing (on the 2ZR-FXE the thermostat is not sold separately from the housing, so it is a "water inlet with thermostat" assembly), new housing gasket, new oil dipstick guide O-ring, Toyota Super Long Life Coolant (SLLC) or an equivalent long-life ethylene glycol coolant (hybrid organic technology, free of silicates, amines, nitrites and borates), about 6 L (6.3 qt)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8- Socket set and ratchet Amazon →
- torque wrench (7-21 N·m / 5-15 lb-ft range) Amazon →
- hose clamp pliers (spring-type) Amazon →
- 9 mm inner diameter hose for draining Amazon →
- coolant drain container (at least 6 L / 6.3 qt) Amazon →
- 6 mm hex key (if the reservoir has an air bleed valve) Amazon →
- gloves Amazon →
- diagnostic scan tool or a way to enter Maintenance Mode Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 5 more.
See manuals →
Step by step
17 steps- The vehicle must be completely cool. Hot pressurized coolant and steam cause severe burns, so do not open the reservoir cap or the radiator drain plug on a hot engine. Park the car on a level surface.
- Remove the rear left engine under cover (Rear Motor Under Cover LH). If there is a main engine under cover below, remove it as well to reach the radiator drain cock.
- Fit the 9 mm inner diameter hose onto the radiator drain cock and put the other end in the container. Loosen the drain cock plug, remove the expansion tank cap, and drain the coolant. After draining, hand-tighten the drain cock plug and remove the hose. Take the used coolant to a recycling facility. Do not pour it on the ground.
- Remove the radiator support opening cover (Radiator Support Opening Cover), then air cleaner inlet No. 2, the air filter case cap, the filter element itself, the air filter case, the case bracket, and air cleaner inlet No. 1. Keep the fasteners organized: the bolts differ in length and torque, so store them by assembly.
- Pull the oil dipstick out of its guide. Release the clip that holds the wiring harness to the dipstick guide. Remove the dipstick guide bolt from the cylinder block, pull the guide out of the oil pan, and take the old O-ring off it.
- Slide back the two spring clamps and remove radiator hose No. 2 and bypass water hose No. 3 from the thermostat housing. To remove hose No. 3, slide back the clamp, twist the hose, and pull it straight off the pipe. Do not put force on the thermostat housing itself and do not damage it.
- Type A: remove the 2 nuts and the bolt, then take off the housing with the thermostat. Type B: remove the 3 bolts. Remove the old gasket from the housing.
- If you want to test the old thermostat, put the housing in water and heat it slowly. The valve should start to open at 80-84 °C. At 95 °C the valve lift should be 10-14 mm (for a conical spring) or at least 8 mm (for a cylindrical spring), and below 77 °C the valve must be fully closed. If the readings do not match, replace it. Either way, install the new assembly with a new gasket.
- Clean the mating surface on the block of any remaining old gasket, without leaving scratches and without dropping debris into the passage.
- Fit the new gasket on the new housing with thermostat and secure it to the block. The tightening torque for the housing nuts and bolts is 10 N·m (7 lb-ft), for both type A and type B. Do not overtighten: the housing is plastic.
- Push hoses No. 2 and No. 3 onto the housing and secure them with the two clamps.
- Lubricate the new dipstick guide O-ring with a thin layer of engine oil, fit it on the guide, insert the lower end into the oil pan, and secure the guide to the cylinder block with the bolt. The bolt tightening torque is 21 N·m (15 lb-ft). Secure the wiring harness with the clip and insert the dipstick.
- Reassemble everything in reverse order: air cleaner inlet No. 1, bracket, air filter case, filter element, cap, inlet No. 2, and the radiator support opening cover. Approximate torques, per the assembly diagram: inlet and air filter case screws about 4 N·m (35 lb-in), clamps about 2 N·m (18 lb-in), air filter case bracket bolts 12-12.5 N·m (9 lb-ft).
- Fill the expansion tank with coolant up to the FULL line. If the reservoir has an air bleed valve, remove it with the 6 mm hex key before filling, then install it afterward at 2 N·m (18 lb-in). The system holds about 5.4 L (5.7 qt) in total (without exhaust heat recovery system) or 6.0 L (6.3 qt) (with the EHRS system). Use only coolant of the required type. Do not use water instead. Squeeze radiator hoses No. 1 and No. 2 by hand several times and top off if necessary.
- Close the reservoir cap as tight as possible. Warm up the engine and bleed the air: turn off the A/C, set the heater control to maximum heat and the fan speed to minimum. On a Prius the engine must run continuously, so enter Maintenance Mode (done by the procedure in the service manual: brake pedal not pressed, POWER button twice without the pedal, then the accelerator pedal in the required sequence). Keep warming up until the thermostat opens (you can tell by feel: when you squeeze hose No. 2, you will feel a vibration from the flow starting), and let it circulate for several minutes. Periodically squeeze radiator hoses No. 1 and No. 2 (wear gloves, since they are hot, and keep your hands away from the fans) to remove air. Make sure there is always coolant in the reservoir. If the temperature gauge shows overheating, shut off the engine and let it cool.
- Shut off the engine, let it cool completely, and check that the level in the reservoir is between the LOW and FULL lines. If it is below LOW, top off to FULL. Inspect the connections for coolant leaks.
- Reinstall the under covers.
Common mistakes and warnings
- Engine overheating caused by an air pocket in the cooling system can lead to serious damage, so do not skip bleeding and level checks
- The hybrid has a high-voltage system: this job does not require touching the orange HV cables, but do not touch or disconnect them, and if you need to work near them, take the car to a repair shop
- If you have no experience with the cooling system and the hybrid's Maintenance Mode, it is better to leave the job to a repair shop
- The air filter fastener torques are approximate, so check the exact values against the manufacturer's specifications
How it works · 3D
How the Engine Cooling System Works
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →