Autopapyrus · Volkswagen Multivan 2.5 TDI AXE (2008)
https://autopapyrus.com/catalog/volkswagen/multivan/guides/unit-injector-adjustment/
https://autopapyrus.com/catalog/volkswagen/multivan/guides/unit-injector-adjustment/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Volkswagen Multivan 2.5 TDI AXE (2008): Unit Injector Adjustment
The 2.5 TDI (R5, AXE) unit injectors are driven from the camshaft through rocker arms. Preload is set with the adjusting screw in the rocker arm: run the screw down until it stops, then back it out 180°. Adjustment is needed after replacing a unit injector, removing the rocker arms, or if you suspect the preload is wrong.
Key figures
- Adjusting screw back-off from the stopafter running the screw down to the stop, back it out exactly this amount (step 8)180° (half a turn)
- Indicator preloadso the probe always touches the rocker arm when measuring the lowest point (step 4)at least 3 mm
- Distance from injector lug to head edgecheck with a caliper after installing a new injector, before tightening the clamp (step 3)151.3 mm ± 0.9 mm
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
5| № | Part | Genuine part no. |
|---|---|---|
| 01 | Rocker arm adjusting screwsif the adjustment is disturbedFind on Amazon → | |
| 02 | Unit injector ball tipsif the adjustment is disturbedFind on Amazon → | WHT002791 |
| 03 | Unit injector O-ringswhen removing the unit injectorsFind on Amazon → | 038198051C |
| 04 | Unit injector clamp boltsnewFind on Amazon → | 070103385A |
| 05 | Cylinder head cover gasketFind on Amazon → | 070103500A |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
9- Socket set and ratchet Amazon →
- torque wrench Amazon →
- long socket or wrench for the rocker arm bolts Amazon →
- dial indicator with stand Amazon →
- caliper (a 400 mm one is needed for the cylinder at the timing belt) Amazon →
- crankshaft turning wrench Amazon →
- unit injector puller (only needed when replacing an injector) Amazon →
- clean rags Amazon →
- engine oil for lubricating the seals Amazon →
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 5 more.
See manuals →
Step by step
13 steps- Let the engine cool down and disconnect the negative battery terminal. Remove the decorative covers and the upper timing belt cover if it blocks access.
- Remove the cylinder head cover. Disconnect the unit injector wiring harness and set it aside. Clean the head around the injectors so dirt doesn't get inside.
- If an injector was replaced, set its angular position first. The clamp is installed only partly tightened, so the injector can still be turned. Use a caliper to measure the distance from the lug on the injector body to the outer edge of the head: 151.3 mm ± 0.9 mm. If the value is out of tolerance, rotate the injector and tighten the clamp bolt. Leave the right jaw of the caliper where it is when you measure the other injectors.
- Mount the dial indicator on the adjusting screw of the injector you're adjusting. The tip must touch the rocker arm on the side that moves down when the injector operates. Preload the indicator by at least 3 mm so the probe always stays in contact with the rocker arm.
- Turn the crankshaft in its normal direction of rotation until the rocker arm of this cylinder is at its lowest point. The indicator needle will stop moving in one direction and start to return. That is the correct point.
- Remove the indicator without disturbing the crankshaft position.
- Loosen the adjusting screw locknut. Screw the adjusting screw in until it stops and you feel strong resistance: the injector plunger has bottomed out in the high-pressure chamber. The screw may be stiff.
- Back the adjusting screw out exactly 180° (half a turn) from this stop. This keeps the plunger from hitting the bottom of the chamber on every cam stroke.
- Hold the screw with a screwdriver or wrench and tighten the locknut. Approximate locknut torque: about 30 N·m (22 lb-ft); confirm the exact value in the manufacturer's service manual.
- Repeat steps 4-9 for each cylinder you are adjusting. Move to the next cylinder by turning the crankshaft until that cylinder's rocker arm is at its lowest point.
- If you removed the rocker arm shaft, use new bolts. First thread them in by hand from the first to the last, then tighten them evenly in the same sequence. Approximate torque: 20 N·m (15 lb-ft) plus a 90° (quarter-turn) angle; confirm the exact value in the manufacturer's service manual.
- If you removed a unit injector: install it with fresh, lubricated O-rings, press it down into its seat, and only then tighten the new clamp bolts in stages (a low torque first, then an angle turn). Don't mix up used injectors between cylinders. Confirm the exact torques and angles for your engine in the manufacturer's service manual.
- Reconnect the harness, install the cylinder head cover with a new gasket, and reassemble the covers. Reconnect the battery, start the engine, and let it idle. Check that it runs smoothly and that there are no fuel or oil leaks.
Common mistakes and warnings
- If an injector isn't pressed down into its seat before the clamp is tightened, you may get hard starting and rough running
- Backing the screw out too little causes plunger and cam wear, and backing it out too much causes unreliable operation
- Don't tighten the clamp bolt before setting the injector's angular position
- This job demands care and cleanliness
- If you have no experience, it's better to leave it to a repair shop
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Volkswagen
Volkswagen proved to the world that a car can be "the people's car": good-looking, affordable and fun.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →