← Polo Volkswagen Polo repair manuals →

Volkswagen Polo (5th generation): Seasonal Tire Swap with Wheel Removal and Balancing

A tire swap on a Polo with the 1.6 MPI engine (CFNA) consists of removing the wheels, demounting and mounting the tires on the rims, balancing, and installing the wheels back on the car. The wheels are held on by five bolts. The key points during installation are a clean mounting surface, tightening in a crisscross pattern, and the final tightening with a torque wrench while the wheel is on the ground.

DifficultyEasy Time1-1.5 hours on your ownremoving and installing the wheels), plus tire mounting and balancing at a shop Steps14

Key figures

  • Wheel bolt tightening torque
    120 N·m (89 lb-ft). Set this on the torque wrench for the final tightening of a wheel that is on the ground (step 10). Less, and the wheel may work loose. More, and you can deform the wheel or strip the threads.
  • Torque check after driving
    after 50-100 km, go over the bolts again with the wrench set to 120 N·m (89 lb-ft) once the bolts have settled (step 13).

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: what to check on a removed wheel and how to tighten bolts

Wheel off the car, seen from the rim side5Tread: pattern depth4Sidewall: cuts, bulges3Rim: cracks, dents1Wheel bolts: 5 holes2Mounting planeTouches the hub, clean rust hereTighten bolts in a cross pattern,final torque 120 NmTap to enlarge
  1. 1Wheel bolts: five bolt holes. Check the threads and do not lubricate them; tighten in a cross pattern, final 120 Nm with a torque wrench.
  2. 2Mounting plane: the flat part of the rim around the center hole, touching the hub. Clean dirt and rust off with a brush before fitting.
  3. 3Rim: check for cracks and dents.
  4. 4Tire sidewall: look for side cuts and bulges, check the tire's age.
  5. 5Tread: the pattern on the tire's running surface, check the remaining depth. Replace worn-out tires.

Parts

3
№Part
01 Set of tires in seasonal sizeFind on Amazon →
02 Wheel balancing weights (adhesive or clip-on, by wheel type)if neededFind on Amazon →
03 Valve stems or valve stem repair kitif neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 16 more. See manuals →

Step by step

14 steps
  1. Park the car on a level, firm surface, put it in first gear, set the parking brake, and place wheel chocks under the wheels on the opposite end of the car.
  2. Mark the wheels with chalk or a marker (FL, FR, RL, RR). This lets you keep the rotation direction of directional tires and rotate the wheels between positions deliberately.
  3. While the car is still on the ground, loosen each wheel bolt about half a turn. If a bolt is very tight, don't jump on the wrench: use a long lever and push down with steady force.
  4. Place the jack under the reinforced area of the sill (at the marked notches) and raise the car until the wheel is off the ground. Never get under a car that is supported only by a jack.
  5. Remove the bolts and take off the wheel. If the wheel is stuck to the hub, tap the side of the tire lightly with a rubber mallet or kick it with your foot.
  6. Inspect the wheels: check the rims for cracks and dents, and check the remaining tread depth, the age of the tires, and the sidewalls for cuts and bulges. Replace any tires that are unfit for use.
  7. At the tire shop, request demounting and mounting of the tires, replacement of the valve stems if necessary, and balancing of each wheel with the old weights removed. If your winter and summer tires are on separate rims, balancing is mandatory.
  8. Before installing, use a brush to clean dirt and rust off the hub mounting surface and the back of the wheel, and check the bolt threads. You may apply a thin coat of grease to the hub centering ring only, so the wheel doesn't seize. Do not put oil or graphite grease on the bolt threads, because it distorts the actual tightening torque.
  9. Place the wheel on the hub, align the holes, thread all five bolts in by hand until they stop, and snug them lightly in a crisscross pattern.
  10. Lower the car until the wheel lightly touches the ground and can't spin, then tighten the bolts in a crisscross pattern. Wheel bolt tightening torque at the hub: 120 N·m (89 lb-ft). Do the final tightening with a torque wrench while the wheel is on the ground.
  11. Repeat for the remaining wheels, lower the car completely, and remove the jack.
  12. Inflate the tires to the pressure specified on the placard in the door opening or inside the fuel filler flap (the value may differ for winter and summer, so check the placard for your trim and load). Check the pressure with the tires cold.
  13. After the first 50-100 km of driving, recheck the bolt torque with the torque wrench (120 N·m (89 lb-ft)) and check the tire pressure again.
  14. It's best to store the removed set in a cool, dark place: stack tires without rims or hang them, and stack tires on rims or hang them by the rims. Wash the wheels beforehand.

Common mistakes and warnings

  • Never work under a car that is supported only by a jack, and never set up a jack on an uneven or soft surface
  • Do not tighten the bolts "all the way" with an impact wrench: exceeding the torque deforms the wheel and strips the threads, while under-tightening can cause the wheel to come off while driving
  • If you have no experience with a jack and a torque wrench, leave wheel removal and installation to a tire shop
  • Fit tires of the same model and wear level on each axle, and for winter use, install a full set on all four wheels
Spotted a mistake? Tell us →

Our articles

More articles →