← Opel

Astra H - problem with the robotized gearbox

Opel Astra 13 answers Translated from Russian · original

Opel Astra H, Z16HER, Easytronic. Here is the history: the ECU stopped communicating (F) and the car would not start. A used unit of the same type from another car was fitted, and the VIN was written with Op-Com. The car seemed to come back to life, with 2 errors after the old ones were cleared, relating to learning and adaptation of the automatic gearbox. After that the clutch was bled through Op-Com and everything went smoothly. All errors were cleared in all modules, but the engine still does not start. I then tried to do the gear-shift adaptation, and during the adaptation the unit froze. The errors came back after clearing: P1734, P1735, U2101, P1600-0B, P1600-0C, P0602-00. I went into the CAN bus and corrected the equipment configuration, and one error (U2101) went away. But if I try to read the VIN or do anything with the adaptation, the unit freezes and resets the CAN bus equipment configuration, and the U2101 error returns. The unit no longer reads the VIN. If I enter VIN programming and try to read it, it says 'wait' forever. When I wrote the VIN earlier, the donor car's VIN was read. When I wrote the customer's car VIN, it was written successfully, was read, and showed in the identification window.

Answers
O
Owner Sep 13, 2020

Hand the car over to professionals.

O
Owner Nov 08, 2020

I'm not a pro, but I'm gaining experience. I've fixed more than 10 Opels, but I've worked with the robotized gearboxes very little, so I'm asking people who know for help. Don't tell me what to do or where the owner of this car should go. You're all experienced and clever, so if you have nothing to answer, pass by.

O
Owner Dec 08, 2020

Check the wiring against the diagram. The power supply may be weak, or the CAN bus may be corroded. Another unit may be interfering with the bus. Also, Op-Com doesn't always work correctly with Easytronic. You can only do the clutch bleeding and the gear adaptation with it. The clutch adaptation will most likely be wrong.

O
Owner Jan 12, 2021

I checked all the wiring from the Easytronic unit to the ECU with a meter. I agree that Op-Com isn't great. I usually do adaptations with Scandoc or Autel, but Op-Com sometimes helps me. There's no point in my buying dealer equipment, since there are no new Opels, and fewer and fewer come to us. The other poster must have problems in the head because of this))) I'm thinking of reflashing the unit (EEPROM). Could this be coming from the electric motors? The brushes, for example?

O
Owner Jan 29, 2021

So what stops you from trying to do the adaptation with Scandoc or Autel?

O
Owner Jun 11, 2021

It's not about the adaptation, it's about the errors. When learning starts, the unit freezes, the equipment configuration on the CAN bus is reset, the U2101 error appears, and the P1600 and P0602 errors stay permanently. These errors were not there when the VIN was programmed. They appeared after the gearbox adaptation, and now during adaptation the unit freezes and resets the equipment configuration. I can't read the VIN from the unit, either in the identification screen or in programming, and I can't rewrite it either.

O
Owner Aug 09, 2021

The motors probably draw a high current because of worn mechanics, or there are power supply problems.

O
Owner Dec 04, 2021

Connect a charger at least during adaptation. The voltage drops during bleeding. The battery can't cope, and the voltage probably drops to 8-9 volts during adaptation. The computer simply goes crazy.

O
Owner Jan 04, 2022

Maybe you're looking in the wrong direction, folks? Is the unit an exact number-for-number match? If not, the CAN addressing differs between cars. The Easytronic may be looking for the engine ECU at the wrong address. Among the rules of good manners is decoding the errors. P0602 can be read as "VIN not programmed". P1734 and P1735 won't go away while P1600 is present in the unit, however much you bleed and re-bleed it ))) Their EEPROM is corrupted, you understand... but who corrupted it? ))) So the problem is solved in two steps: reprogramming plus adaptation. And I'd bet that Tech2 plus MDI will solve the problem. Or, in a less common case, the Easytronic is faulty. But that's a separate topic...

O
Owner Feb 01, 2022

At the moment of adaptation you need to watch which procedure the adaptation hangs on. If it hangs when the clutch is pressed, something is wrong with the clutch (for example a non-original or worn clutch, or faulty hydraulics). If it hangs during gear engagement adaptation, it may be wear of the plastic pads on the forks, or wear on the gear-selection actuator shaft. Fork wear shows up as an atypical fork travel distance compared with the others. Remove the selection actuator and engage the gears with a screwdriver to check.

O
Owner Mar 08, 2022

I did a couple of cars with Autocom without problems. Op-Com was slow, especially with the Zafira!

O
Owner Mar 28, 2022

Maybe you're looking in the wrong direction, folks? Is the unit an exact number-for-number match? If not, the CAN addressing differs between cars. The Easytronic may be looking for the engine ECU at the wrong address. Among the rules of good manners is decoding the errors. P0602 can be read as "VIN not programmed". P1734 and P1735 won't go away while P1600 is present in the unit, however much you bleed and re-bleed it ))) Their EEPROM is corrupted, you understand... but who corrupted it? ))) So the problem is solved in two steps: reprogramming plus adaptation. And I'd bet that Tech2 plus MDI will solve the problem. Or, in a less common case, the Easytronic is faulty. But that's a separate topic...

O
Owner Dec 24, 2022

P1600 and P0602 in the new unit? Re-flash the flash and EEPROM. If that doesn't help, the unit is faulty and it's better to return it.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →